ParaBody 866103 manual Upright Frame

1,

o

Insert one (1) 3 X 2 IN. ENDCAPinto the top of the UPRIGtITFRAME,and two (2) 2 IN. SQ. CAPSinto the BASEof the UPRIGHTFRAMEas shown on drawing. Repeat this step for the second

UPRIGHT FRAME.

SECURELYassemble both UPRIGHTFRAMESto the CROSSBRACEas shown on drawing using four (4) 1/2 X 3 IN. BOLTS,four (4) 1/2 IN. WASHERS,and four (4) 1/2 IN. LOCK (IMPORTANT: ~ ANGLE BRACKETS ON ~ CROSS BRACE ARE OFFSET, PLEASE MAKE SURE THAT ~ LONGEST END OF TIlE BRACKET IS FACING IYP BEFORE ASSEMBLY)

SECURELYassemble the BENCHFRAMEto the CROSSBRACEas shown on dmw~ngusing two (2) 1/2 X 3 IN. BOLTS,two (2) 1/2 IN. WASHERS,and two (2) 1/2 IN. LOCKNUTS.Attach one 2" cover cap to the BENCHFRAMEas shown.

Insert two (2) 1/2 IN. FLANGEBEARINGSinto each end of the BUSHINGof the BLENCHFRAME shown on drawing.

SECURELYassemble the BENCHSLIDE to the BUSHINGof the BENCHFRAMEas shown on drawing, using one (1) 1/2 X 3-1/2 IN. BOLTone (1) 1/2 IN. LOWHTLOCK

Attach eight (8) 1-1/2 X 3/4" GLIDESto the WOLFFSLEEVE(FOURONEACHEll'D) as shown (DETAILA) using the following steps:

¯Thoroughlyclean all surfaces wherethe GLIDESare to be attached.

¯Removethe GLIDESfrom the paper backing and f'mrdy apply them to all shownsurfaces.

Insert one (1) U-PIN through the BUSItlNGof the WOLFFSLEEVEas shown on ctrawing, and attach one (1) PALNUTto the end of the U-PIN.

SECURELYAssemble one (1) SPRINGPIN ASSEMBLYto the SPRINGPIN BARI~',L, of the WOLFFSLEEVEas shown in (DETAIL B). (!!! IMPORTANT!!! TIGHTENTLTE NUT OF SPRING PIN ASSEMBLY SECURELY)

Pull back the SPRINGPIN on the WOLFFSLEEVEand slide it over the end of the BENCHSLIDEas shown on drawing. Engage the SPRINGPIN into one of the adjustment holes. Secure tk~e WOLFF SLEEVEin place with one (1) 3-PRONGKNOB.

10.LOOSELYassemble one (1) 3 PRONGKNOBto the UPRIGHTTUBEof the BENCI~[ FRAME

shown on drawing. (TI:[IS WILL BE USED TO SECUREATTACHMENTSIN PLACE)

11.Attach one (1) 1-1/4 IN. SQ. RUBBERBUMPERto the SLIDESUPPORTas shown orb drawing.

12.SECURELYassemble the SLIDE SUPPORTto the end of the BENCHSLIDE as shown on drawing using one (1) 3/8 X 2-3/4 IN. BOLT,two (2) 3/8 IN WASHERS,and one (1) 3/8 IN. LOCK

13.Attach two (2) 1 X 1 GLIDESto file top of the BENCHFRAMEwhere the SLIDESUPPORTmakes contact. See drawing.

14.Assemble the SEATPADto the WOLFFSLEEVE,start by sliding t~vo (2) HINGETABSover the PIN of the WOLFFSLEEVE(ONE ON EACHSIDE) as shown on drawing, and SECURELY assemble each tlINGE TABto the SEATPAll using two (2) 3/8 X 1-1/4 IN. BOLTSmid two (2) IN. WASHERS. (MAKE SURE BOTH ltINGE TABS ARE ALL THE WAYON TIlE PIN)

Part # 6657601 3 Revision: it0/28/96