894 PROSYSTEM PEC DEC OPTION ASSEMBLY INSTRUCTIONS

Removethe SECONDARYCABLEby disassembling the CABLEfrom its ,M.,~IX UPRIGIII'I" CONNECTIONPOINT, and pull CABLEout from the LOWPULLEYSTATION. (NOTIE:

REMOVELG,W PULLEY FOR EASE OF REMOVAL)

Insert four (4) 2 IN. SQ. ENDCAPSinto all open ends of the BEARINGltOt.!SING.

Insert one (I) ";'. IN. SQ. ENDCAPinto the end of the PULLEYMOUNTSUPPORT,

SECURELY~ssemble both the BEARINGHOUSINGand the PULLEYMOUNTSUPPOR'[ to the MAINUPRIGHTof the BODYSMITHPROSYSTEM,using two (2) I~ X 3-I,r2 IN. BOLI'S, four 1/2 IN. WASHERS,two (2) t/2 IN. LOCKWASHERS,and two (2) 1,2 IN. NUIS.

NOTE: THE CONNECTORPLATES ON THE BEARING HOUSING AND TIlE PI.:i, LEY MOUNT SUPPORT HA.VE OVAL HOLES. MOVETHE BEARING HOUSING DO~,VN AND TIlE PULLEY MOUNTSUPPORT UP AS FAR AS POSSIBLE. SEE-DRAWING

CAREFULLYinsert tour (4) FLANGEBEARINGSinto the TOP and BOTTOMside~ of the

BUSHINGSof the BEARINGHOUSINGon both sides. (CAUTION: DO NOT OVERTAP TItESE BEARINGS INTO PLACE, WHICH CAN CAUSE DEFORMATIONTO TIlE BEARINGS, MAKING THEM UNUSABLE)

Insert four (4) 2 IN. SQ. ENDCAPSinto BOTHENDSof the LEFT and RIGliT PEC-DECARMS.

Insert the LEFT and RIGHTPEC-DECARMSthrough the FLANGEBEARINGSin the BEARING HOUSINGon their respective sides, and secure them in place with two (2) STARLOCKCOLLARS.

Attach two (2) PLASTICSTOPSto the CAMSTOPon the BEARINGHOUSING,approximately where shown, in orde.r to give the PEC-DECARMCAMSfull contact when the PEC-DECARMS~tre in their restingpositio~a.

Slide two (2) 4 X 12 ROLLERPADSonto the LEFTand RIGHTPEC-DECARMS.until the ROLLER PAD is FLUSHwith the bottom of the ARMS.(NOTE:IF A LUBRICANTIS REQUIRED,RUBBING ALCOHOLTHOROUGHLYCOATING THE INSIDE OF THE ROLLER IS TIlE BF2~-I"

MATERIALTO USE. ALSO, ROTATING THE PAD ~'HILE PUSHING UP WILL llELP TO EASE ASSEMBLY)

10.LOOSELYassemble two (2) 4-1/20.D. X I IN. BUSHINGPULLEYSand tx~o {2} CAIILI:'. RETAININGCLIPS to the PULLEYMOUNTSUPPORT.usiqg tx~o (2~

IN. LOCKWASHERS,and two (2) 3/8 IN. NUTS.(NOTE: Tills CONNECTIONX~II..i.

TIGHTENED AFTER THE CABLE HAS BEEN ROUTED)

II.LOOSELYassemble the BACKPADto the TOPHOLEof the MAINVPRIGlt I. u,,mg t~,ne ( i } 3;g X IN. BOLT,one (1) 3/8 IN. LOCKWASHER,and one (!) 3,'8 IN. ~,VASllER

12."

Using one (1)3/8 X 3-I/4 IN. BOLT,and one (I)3i8 IN. LOCKWASIIER.SECt REI.~' assemble

LOWERPULLEYSUPPORTthrough the BOTTOMHOLEof the MAINUI'RIf;liT and into the

 

 

BACKPAD. (NOTE: MAKESURE THAT THE BASE PLATE OFTilE

L¢)~ t:R I'ILLEY

 

SUPPORTIS

FLUSH WITHTHE SIDES OF THE MAINUI'RI(;IIT.

SEE I)R.~I~(J;I

13.

TIGHTENthe

BOLr in STEP ! I.

 

Page 4
Image 4
ParaBody 894 manual Prosystem PEC DEC Option Assembly Instructions, REMOVELG,W Pulley for Ease of Removal