Configuration Worksheet for Basic Mode

Date:_______________________________________________ Location:____________________________________________ Local Phone No.: ( j)_____________________________

Device:_____________________________________________ Local Address:________________________________________ j DBM Installed

Serial No.:___________________________________________ Tributary Network Address:______________________________ j SNA Diagnostic Interface (LPDA-2) Installed

DSU Options Value
Rate(Kbps) 64CC, 64L, 56, 38.4, 19.2, 9.6, 4.8, 2.4
PrtSp(Kbps) 64, 56, 48, 38.4, 32, 28.8, 19.2, 18.8,
18.0, 16.8, 14.4, 12.0, 9.6, 9.2, 8.4, 7.2,
4.8, 4.4, 4.0, 2.4 , 2.0, 1.2, Disab
TxClkSource Int, RXC, Ext, DDS
Msg Clamp Enab, Disab
TxElasStor Enab, Disab
RxElastStor Enab, Disab
19.2 PowrLvl +6, 0, –10
64KScramblng On, Off
64KLatchLpbk On, Off
AggrSwitch Enab, Disab
AgSw Timing Int, Aggr, Prt1
V.54 Lpbk Enab, Disab
General Options Value
DTE Port EIA232, V.35
RTS Cntrl FrcOn, DTE
CTS Cntrl Std, =RTS
AntiStream
(Chang)
Disab, 1– 100 sec
LSD Lead Std, Delay, FrcOn
CTS Lead Std, Delay, FrcOn
DSR FrcOn Enab, Disab
SystemStat Enab, Disab
DSR on Tst Enab, Disab
Circ Assur Enab, Disab
Tst Pattern AT&T, Std
RespondRDL Enab, Disab
LL by DTE Enab, Disab
RL by DTE Enab, Disab
Bilat Lpbk Enab, Disab
Ext Leads ExtLd, Rate, RPowr
CCN by EL Enab, Disab
DTR Alarm Enab, Disab
SW Vers 3.22, 4.41, Normal
AnswExtBU Enab, Disab
Async→Sync Enab, Disab
AsyncBit/Char 6, 7, 8, 9, 10
Stop Bits 1, 2
Overspeed 1.0, 2.3
Diagnostic DSU Options Value
Diag Type NonD, Disr, Mixed, None
2nd Ch(bps) 100, 400, 800, 1200, 1600
Disr Type 2500, 2600, 3600s, 3600e, Br56
Diagnostic DBM Options Value
Diag Type NonD, Disr, Mixed, None
2nd Ch(bps) 100, 400, 800, 1200, 1600
RemoteDiag V.54, Enhan, 2500
Diagnostic General Options Value
Position Cntrl, Trib, G2Trb
LinkConfg Pt-Pt, M-Pt
Resp Period 1, 2, 10
TribTimOut
(Chang)
sec to min (5 sec to 10 min)
Diag Conn CC, DC
Link Delay 0s, 1s, 2s, 5s, 10s, 20s, 50s
Network Delay 0s, 1s, 2s, 5s, 10s, 20s, 50s
Packet Delay 0s, 1s, 2s, 5s
M-Pt SymPrt Enab, Disab
Fast Sel Enab, Disab
Backup Options Value
Auto Bckup Enab, Disab
Backup Dir
(Chang)
(1–10)
BckupOnCMI Enab, Disab
AutoRestor Enab, Disab
NtwkTimOut
(Chang)
min and sec (1 to 30 min)
RestorTimOut
(Chang)
min and sec (1 to 60 min)
TriesTimeOut
(Chang)
min and sec (1 to 60 min)
MultiCall Enab, Disab
ChgMd Options Value
Mode DPII, ADp, DMC
Hardware Straps Value
DDD Interface{Permissive, Programmable
Frame Ground/Signal Ground Connected, Disconnected
Test Mode Indication Enabled, Disabled
DBM Options Value
Rate(Kbps){14.4, 12.0, 9.6, 4.8, 2.4
PrtSp(Kbps) 56, 48, 38.4, 32, 28.8, 19.2, 18.8, 18.0,
16.8, 14.4, 12.0, 9.6, 9.2, 8.4, 7.2, 4.8,
4.4, 4.0, 2.4, 2.0, 1.2, Disab
TxClkSource{Int, RXC, Ext, DSU
CarrLossDisc{Yes, No
Auto Retrain{Yes, No
Single Rate{Yes, No
AutoAnswer Enab, Disab
TxElasStor Enab, Disab
RxElasStor Enab, Disab
Call Setup None, Pswrd, Cllbk, Alarm
RxPwd
(Chang)
(up to 10 digits)
TxPwd
(Chang)
(up to 10 digits)
V.13 Signl Enab, Disab
Dial Test Enab, Disab
Primary Core Yes, No
DTRCallCon Orig{{, Ansr, Disab
EchoCancel* Enab, Disab
Remot DBM** 2-wire, 4-wire
{Not available if a Switched 56 DBM *Switched 56 DBM only
{{Not available if Primary Core is No **2-wire Switched 56 DBM only
Backup Directory Dial String
1
2
3
4
5
6
7
8
9
10
LPDA-2 Options Value
LPDA-2 Enab, Disab
LPDA Address
(Chang)
(1 – 256)
SNA Backup Enab, Disab
Code 1
(Chang)
Code 2
(Chang)