Paradyne 3160, 3164, and 3165 E-6

SNMP MIB Objects

E-6 3160-A2-GB21-80March 1999

Interface Group – “ifDescr” Object (ifEntry 2)

This object provides information about the interface. Each interface displays a

text string as shown below:

Network T1: “Network T1. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the CSU board]”.

DTE T1: “DTE T1. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the CSU board]”.

COM: “COM port. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the CSU board for the standalone,

or the CCA number for the DSU board for the carrier]”.

Modem: “MODEM port. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the CSU board]”.

AUX: “AUX port. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the CSU board]”.

Data Ports: “Data Port n. [

Company Name

] T1 DSU/CSU, Hardware

Version: [CCA number for the DSU board]”

(where

n

is 1 to 4).

Interface Group – “ifType” Object (ifEntry 3)

This object identifies the type of the interface based on the physical/link

protocol(s) immediately below the network layer. Only the following values are

supported by the DSU/CSU:

ds1 – Used for the network and DTE Drop/Insert (DSX-1) interfaces.

propPointToPointSerial(22) – Used for the synchronous data ports. Used for

the MODEM or COM port when the port is not configured as the SNMP

management interface.

ppp(23) – Used for the MODEM, AUX, or COM port when the port is

configured for PPP.

slip(28) – Used for the MODEM or COM port when the port is configured for

SLIP.

Interface Group – “ifMtu” Object (ifEntry 4)

This object identifies the largest datagram that can be sent or received on the

interface. It is applicable only to the interface configured as the SNMP

management link. This object is zero for all other interfaces.

Contents

Main A Copyright 1999 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice Warranty Registration Service & Support Warranty, Sales, Service, and Training Information B !Important Safety Instructions C Direct Feed Power Supply Warning EMI Warnings D Government Requirements and Equipment Return United States NOTICE TO USERS OF THE UNITED STATES TELEPHONE NETWORK 316x DSU/CSU Facility Interface Codes Code Description E CAUTION: i Contents About This Guide 1 Introduction 2 Installation ii 3 Operation iii 4 Maintenance iv A Front Panel Menu B Technical Specifications C Configuration Options v D Pin Assignments E SNMP MIB Objects Page vii About This Guide Document Purpose and Intended Audience Document Summary Section Description viii Product-Related Documents Document Number Document Title ix Reference Documents Page 1-1 Introduction 1 Features 1-2 DTE Drop/Insert (DSX-1) Interface Alarm Message Capability Front Panel Emulation Integral Modem Async Terminal Interface Support Physical Description Standalone DSU/CSU Front Panel 1-4 F1 F2 F3 Figure 1-2. 3164 DSU/CSU Front Panel 3164 3160 Standalone DSU/CSU Rear Panel 1-6 CAUTION: Figure 1-6. 3165 DSU/CSU Rear Panel CAUTION: Figure 1-5. 3164 DSU/CSU Rear Panel 1-7 Table 1-1. Standalone DSU/CSU Rear Panel Connectors Name Function Page 2-1 Installation 2 Application Examples 2-2 NETWORK Figure 2-3. Fractional T1 Application Example Figure 2-1. Point-to-Point Application Example NETWORK SERVICES SNMP or Telnet Connection Examples NETWORK 2-4 NETWORK Figure 2-8. Remote Access through FDL/EDL NETWORK LAN ROUTERETHERNET Important Instructions Important Safety Instructions !HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES Optional Power Sources Installing the Single 48 Vdc Power Supply 2-7 Installing the Redundant 48 Vdc Power Supply 2-8 Cabling Examples Figure 2-12. Cabling Examples Pin Assignments Figure 2-12 illustrates some cabling examples. PSTN Power-Up Self-Test 2-10 Maintenance Self-Test Health 3-1 Operation 3 Using the Front Panel 3-2 LCD Device Health and Status 3-3 Keypad 3-4 Test Jacks Test Jacks 3-5 LEDs Selecting the DTE Drop/Insert or Data Port for LED Display 3-6 Table 3-1. System LEDs Table 3-2. Network Interface LEDs (1 of 2) 3-7 Table 3-2. Network Interface LEDs (2 of 2) Name MeaningColor 3-8 Table 3-3. DTE Drop/Insert (DSX-1) Interface LEDs (2 of 2) Name MeaningColor Table 3-4. Data Port LEDs (1 of 2) 3-9 Displaying Unit Identity 3-10 3-11 Setting Customer Identification 3-12 Selecting the DTE Drop/Insert or Data Port for LED Display 3-13 Displaying LED Conditions Front Panel Emulation 3-14 Changing Configuration Options 3-15 3-16 Displaying/Editing Configuration Options 3-17 Saving Edit Changes 3-18 Selecting/Copying to a Specific Port Configuration 3-19 from IP Network Addressing Scenarios Configuring the DSU/CSU for SNMP or Telnet Access 3-20 Selecting the Port 3-21 Setting the IP Address xxx.xxx.xxx.xxx IP Network Addressing Scenarios 3-22 000.000.000.000 3-23 Selecting the Link Layer Protocol Selecting the Port 3-24 Specifying the Community Name(s) and Access Type(s) 3-25 3-26 Configuring SNMP Traps SNMP Traps Enabling SNMP Trap Messages 3-27 Selecting the Number of Trap Managers 3-28 Configuring a Destination for SNMP Traps n Setting the IP Address 000.000.000.000 3-29 Configuring DS0 Channels Allocating Data Ports 3-30 Figure 3-6. Example of Channel Allocation 3-31 Network Interface Network Channel Allocation Figure 3-7. Example of Interface Worksheet for Network Interface 3-32 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation Figure 3-8. Example of Interface Worksheet for DTE Drop/Insert Interface 3-33 DTE Chan Config Assign: (N1 24) Voice (RBS or Data) Figure 3-9. Example of RBS Information Worksheet 3-34 Conf Options Value Figure 3-10. Port Channel Configuration Worksheet (Ports 1 and 2) 3-35 Conf Options Value Figure 3-11. Port Channel Configuration Worksheet (Ports 3 and 4) 3-36 Displaying DS0 Channel Assignments 3-37 3-38 Allocating Data Ports 3-39 3-40 Block or ACAMI Assignment Method 3-41 Individual Channel Assignment Method 3-42 Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface 3-43 n. 3-44 Clearing DS0 Channel Allocation 3-45 Providing Backup Capability Selecting the Timing Source 3-46 Configuring for Network Timing Configuration Options Configuring for External Timing 3-47 Configuring for Network Timing Configuring for External Timing 3-48 Establishing Access Security on a Port Setting a Password 3-49 Setting a Password Establishing Access Security on a Port 3-50 Entering a Password to Gain Access Setting a Password 3-51 Acquiring/Releasing the User Interface 3-52 Acquiring the Active User Interface 3-53 Releasing the Active User Interface 3-54 Enabling/Disabling the Front Panel 3-55 Using the Integral Modem in Standalone DSU/CSUs User Interface Configuration Options Entering Numbers in the Phone Directories 3-56 3-57 Initiating a Call for Front Panel Pass-Through Operation Configuration Options), 3-58 3-59 Initiating a Call for PC, ASCII Terminal/Printer, or SNMP Operation 3-60 Disconnecting the Modem Connection 3-61 Enabling the Communication Port for Carrier-Mounted DSU/CSUs COMSPHERE 3000 Series Carrier Installation Manual 3-62 3-63 Table 3-7. Control Sequence Sequence ASCII HEX 3-64 Deactivating the Alarm Relay for Carrier-Mounted DSU/CSUs 3-65 Resetting the DSU/CSU Download Operations Page 3-67 User Interface Access Security for Standalone DSU/CSUs 3-68 Changing User Interface Access Security 4-1 Maintenance 4 Installation Self-Test Health 4-2 4-3 Device Health and Status 4-4 Table 4-2. Device Health and Status Messages (1 of 2) Message Description xxxxxxxx 4-5 Performance Reports 4-6 xx,xxx 4-7 xx xxx 4-8 4-9 Table 4-3. Performance Registers (2 of 3) Register Totals DescriptionInterval Description 4-10 Table 4-3. Performance Registers (3 of 3) Register Totals DescriptionInterval Description 4-11 Alarms 4-12 Alarm Configuration Configuring SNMP Traps SNMP Traps 4-13 4-14 Troubleshooting 4-15 Table 4-6. Troubleshooting (2 of 3) Symptom SolutionsPossible Cause 4-16 Table 4-6. Troubleshooting (3 of 3) Symptom SolutionsPossible Cause 4-17 Test Jacks 4-18 Figure 4-2. Test Jack Block Diagram Table 4-7. Test Jack Functions Test Jack Name Function 4-19 Test Commands Remote Loopback Tests 4-20 Sending a Line Loopback Up or Down 4-21 Sending a V.54/ANSI FT1 Activation/Deactivation Type 4-22 Local Loopback Tests 4-23 Starting a Line Loopback 4-24 Starting a Payload Loopback 4-25 Starting a DTE Loopback 4-26 Starting a Repeater Loopback 4-27 Starting a Data Channel Loopback 4-28 Starting a Data Terminal Loopback 4-29 Aborting Loopbacks 4-30 Test Name Test Patterns 4-31 Sending Test Patterns Name 4-32 Name and Dest 4-33 Monitoring Test Patterns Name 4-34 Aborting Test Patterns 4-35 Send or Mon Lamp Test Starting a Lamp Test 4-36 Aborting a Lamp Test 4-37 Displaying DSU/CSU Test Status Page Page Front Panel Menu A-2 B-1 Technical Specifications B Table B-1. Models 3160/3164/3165/DSU/CSUs Technical Specifications (1 of 2) Specifications Criteria Technical Specifications B-2 Table B-1. Models 3160/3164/3165/DSU/CSUs Technical Specifications (2 of 2) Specifications Criteria C-1 Configuration Options C C-2 DTE Interface Configuration Options C-3 Table C-1. DTE Interface Configuration Options (2 of 2) Port Configuration Options Table C-2. Port Configuration Options (1 of 5) C-4 Table C-2. Port Configuration Options (2 of 5) C-5 Table C-2. Port Configuration Options (3 of 5) C-6 Table C-2. Port Configuration Options (4 of 5) C-7 Table C-2. Port Configuration Options (5 of 5) C-8 Network Interface Configuration Options Table C-3. Network Interface Configuration Options (1 of 3) C-9 Table C-3. Network Interface Configuration Options (2 of 3) C-10 Channel Configuration Options C-11 Table C-4. DTE Channel Configuration Options n, C-12 Table C-5. Data Port Channel Configuration Options (1 of 4) Operation Configuring DS0 Channels C-13 Table C-5. Data Port Channel Configuration Options (2 of 4) C-14 Table C-5. Data Port Channel Configuration Options (3 of 4) C-15 Table C-5. Data Port Channel Configuration Options (4 of 4) n, OR C-16 General Configuration Options Table C-6. General Configuration Options (1 of 2) C-17 Table C-6. General Configuration Options (2 of 2) C-18 User Interface Configuration Options C-19 Table C-7. User Interface Configuration Options (2 of 10) C-20 Table C-7. User Interface Configuration Options (3 of 10) C-21 Table C-7. User Interface Configuration Options (4 of 10) C-22 Table C-7. User Interface Configuration Options (5 of 10) X.X C-23 Table C-7. User Interface Configuration Options (6 of 10) C-24 Table C-7. User Interface Configuration Options (7 of 10) C-25 Table C-7. User Interface Configuration Options (8 of 10) C-26 Table C-7. User Interface Configuration Options (9 of 10) C-27 Table C-7. User Interface Configuration Options (10 of 10) Alarm Configuration Options C-28 Table C-8. Alarm Configuration Options (2 of 4) C-29 Table C-8. Alarm Configuration Options (3 of 4) C-30 Table C-8. Alarm Configuration Options (4 of 4) C-31 Management Configuration Options C-32 Table C-9. General Management Configuration Options (2 of 7) C-33 Table C-9. General Management Configuration Options (3 of 7) C-34 Table C-9. General Management Configuration Options (4 of 7) C-35 Table C-9. General Management Configuration Options (5 of 7) C-36 Table C-9. General Management Configuration Options (6 of 7) C-37 Table C-9. General Management Configuration Options (7 of 7) C-38 Table C-10. Management Trap Configuration Options (1 of 3) C-39 Table C-10. Management Trap Configuration Options (2 of 3) C-40 Table C-10. Management Trap Configuration Options (3 of 3) C-41 Configuration Worksheets C-42 C-43 C-44 Prt1 Options Value (Default in Bold) Prt2 Options Value (Default in Bold) C-45 Prt3 Options Value (Default in Bold) Prt4 Options Value (Default in Bold) C-46 Network Interface Network Channel Allocation C-47 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation C-48 DTE Chan Config Assign: (N1 24) Voice (RBS or Data) C-49 Conf Options Value (Default in Bold) C-50 Conf Options Value (Default in Bold) C-51 C-52 D-1 Pin Assignments D Equipment List T1 Network Interface Page D-3 DTE Drop/Insert Interface DTE Interface Configuration Options D-4 MODEM Port Interface D-5 AUX Port Interface D-6 COM Port Interface Page D-8 EIA-530-A Port Interface Connector Number Direction Pin D-9 EIA-530-A-to-RS-449 Cable Interface Figure D-7. EIA-530-A-to-RS-449 Adapter The EIA-530-A-to-RS-449 adapter (Figure D-7) provides the RS-449 interface shown in Table D-8. D-10 Table D-8. RS-449 Cable Interface Signal Circuit Mnemonic ITU-T Number Direction Pin D-11 EIA-530-A-to-V.35 Cable Interface Figure D-8. EIA-530-A-to-V.35 Adapter The EIA-530-A-to-V.35 adapter (Figure D-8) provides the V.35 interface shown in Table D-9. D-12 Table D-9. V.35 Cable Interface Signal ITU-T Number Direction Pin D-13 EIA-530-A-to-X.21 Cable Interface The EIA-530-A-to-X.21 adapter (Figure D-9) provides the X.21 interface shown in Table D-10. D-14 Serial Crossover Cable Figure D-10. Serial Crossover Cable D-15 Power Input Connector Optional DC Power Cable Installation D-16 External Clock Interface E-1 SNMP MIB Objects E E-2 MIB II (RFC 1213) ssssssss zzzz-zzz yy.yy.yy zzzz-zzz E-3 E-4 Interface Group, MIB II E-5 E-6 E-7 E-8 E-9 E-10 IP Group, MIB II E-11 E-12 E-13 ICMP Group, MIB II TCP Group, MIB II UDP Group, MIB II Transmission Group, MIB II E-14 DS1/E1 MIB (RFC 1406) Near End Group, DS1/E1 MIB E-15 E-16 E-17 E-18 Far End Group, DS1/E1 MIB E-19 DS1 Fractional Group, DS1/E1 MIB RS-232-like MIB (RFC 1317) E-20 General Port Table, RS-232-like MIB E-21 E-22 Asynchronous Port Table, RS-232-like MIB E-23 Synchronous Port Table, RS-232-like MIB Input Signal Table, RS-232-like MIB E-24 Output Signal Table, RS-232-like MIB Generic-Interface MIB Extensions (RFC 1229) E-25 Generic Interface Test Table, Generic Interface MIB E-26 E-27 Enterprise MIB E-28 Correlation between Menu Commands and SNMP Objects values for SNMP objects are displayed in italics. E-29 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (1 of 4) dsx1LossOfSignal dsx1LossOfFrame dsx1RcvFarEnd dsx1RcvAIS dsx1OtherFailure dsx1LossOfSignal dsx1LossOfFrame dsx1RcvFarEnd dsx1RcvAIS E-30 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (2 of 4) E-31 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (3 of 4) E-32 Table E-1. SNMP MIB to Front Panel Command Cross-Reference (4 of 4) F-1 IP Network Addressing Scenarios F F-2 Scenario 1 F-3 Scenario 2 F-4 Scenario 3 IP Network Addressing Scenarios F-5 Scenario 4 Figure F-4. Local Carrier Connected to Remote Carriers an Alternative 135.19.6.1 . . . . 135.19.6.16 135.19.20.1 . . . . 135.19.20.16 135.19.1.1 . . . . 135.19.1.16 Scenario 5 G-1 Front Panel Emulation G ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Installing Front Panel Emulation Software G-2 G-3 Starting Front Panel Emulation G-4 Displaying LED Conditions H-1 Asynchronous Terminal Operation H Configuring the DSU/CSU for SNMP or Telnet Access Before Using the Asynchronous Terminal Changing Configuration Initiating an Asynchronous Terminal Session Entering a Password to Gain Access IP Network Addressing Scenarios H-3 Ending an Asynchronous Terminal Session H-4 Menu Organization Figure H-2. Menu Organization H-5 Using Asynchronous Terminal Screens H-6 NOTES: H-7 Setting Customer Identification H-8 Displaying LED Conditions H-9 Changing Configuration Options Changing Configuration Options Displaying or Editing Configuration Options H-10 H-11 Saving Edit Changes H-12 Establishing Access Security on a Port Setting a Password H-13 Setting a Password Establishing Access Security on a Port H-14 Entering a Password to Gain Access If an invalid password is entered three consecutive times If the password is invalid If the password is valid Configuration Worksheets for the Asynchronous Terminal Interface H-16 (Port 1) Front Panel Equivalent Value (Default in Bold) H-17 (Port 2) Front Panel Equivalent Value (Default in Bold) H-18 (Port 3) Front Panel Equivalent Value (Default in Bold) H-19 (Port 4) Front Panel Equivalent Value (Default in Bold) H-20 H-21 User Interface: External Device Options Front Panel Equivalent Value (Default in Bold) User Interface: Telnet Sessions Options Front Panel Equivalent Value (Default in Bold) User Interface: Internal Modem Options Front Panel Equivalent Value (Default in Bold) H-22 User Interface: Auxiliary Port Options Front Panel Equivalent Value (Default in Bold) Alarm and Trap Options Front Panel Equivalent Value (Default in Bold) H-23 Page I-1 Equipment List I and the Cable numbers for the 3161 DSU/CSU are located in the Equipment Feature Number ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide Page GL-1 Glossary GL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 GL-9 GL-10 IN-1 Index A B C IN-2 D E F IN-3 G I K L M N O P IN-5 Q R S T IN-6 U V W X Y