Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 2172 user manual Appendix A

Models: 2172

1 22

Download 22 pages 12.19 Kb

Page 18

APPENDIX A

SPECIFICATIONS

A.1 LAN CONNECTION

•Shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet

•CopperLINK Connection: RJ-45 or Terminal Block

A.2 TRANSMISSION LINE

Two-wire unconditioned twisted pair.

A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE

•Line Rate: 50 Mbps, symmetric upstream/downstream. Additional symmetric and asymmetric rates are available via DIP switch settings.

•Distance: 6,000 ft (1.8 km) at 1 Mbps upstream/4 Mbps downstream

Note Distances depend on selected line rate and line conditions. See Appendix D on page 21 for details.

A.4 COPPERLINK SURGE SUPPRESSOR

SIDACTOR with maximum current surge: 20 kA (8/20 ∝s).

A.5 LED STATUS INDICATORS

•Power (Green)

•CopperLINK: Link (Green)

•Ethernet: Link (Green) & Activity (Flashing Green)

A.6 POWER SUPPLY

External AC and DC options:

•AC: 120 VAC, 220 VAC, and UI (120–240 VAC)

•DC: 12 VDC, 24 VDC and 48 VDC

•Power consumption: 450 mA at 5 VDC

A.7 TEMPERATURE RANGE

0–50°C

A.8 HUMIDITY

Up to 90% non-condensing.

A.9 DIMENSIONS

1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm)

18

Image 18

Patton electronic 2172 user manual Appendix A

Contents

CopperLINK High Speed Ethernet Extenders USER MANUALMODEL An ISO-9001Certiﬁed CompanyCONTENTS RJ-45 Distance Chart, Based on 24 AWG 0.5 MM10/100Base-T Interface CopperLINK Interface1.1 COMPLIANCE EMC Compliance 1.0 WARRANTY INFORMATIONSafety Compliance 1.2 RADIO AND TV INTERFERENCE FCC PART1.4 SERVICE 1.3 DECLARATION OF CONFORMITYTel +1 301 Email support@patton.com 1.5 SAFETY WHEN WORKING WITH ELECTRICITY 2.1 FEATURES 2.0 GENERAL INFORMATION2.2 DESCRIPTION external use and shall be rated for the proper applica 3.0 INSTALLATION The Interconnecting cables shall be acceptable forCAUTION perature, ﬂammability, and mechanical serviceability tion with respect to voltage, current, anticipated tem2172 RJ-45 2172 Terminal block 1 no connection Figure 5. Model 2172 10/100Base-T RJ-45 Connector Pinout Power EthernetFigure 4. Model 2172 Terminal Block twisted pair line interface The Model 2172 does not have a power switch, so it powers up as soon as it is plugged in Figure 6. Removing protective cover Figure 7. DIP switch orientationPower High Speed Ethernet ExtenderCopperLINK4.2 CONFIGURING DIP SWITCH S2 S2-8 Table 4 Asymmetric CopperLINK Line Rates Selection ChartS2-7 Table 5 Ethernet conﬁgurations5.1 POWER UP 5.0 OPERATION5.2 FRONT PANEL LED STATUS MONITORS Power APPENDIX A Only required with optional UI power supply 08055DCUI Power SuppliesPower Cords Base ModelsC.1 10/100BASE-T INTERFACE RJ-45 Power EthernetAPPENDIX C C.2 COPPERLINK INTERFACE RJ-45DISTANCE CHART, BASED ON 24 AWG 0.5 MM Copyright 2001, 2002 Patton Electronics Company All Rights Reserved