Peavey 12 D manual Impulse 12D

ENCLOSURE: Peavey Impulse® 12D

FREQUENCY RESPONSE: 52 Hz to 20 kHz

LOW FREQUENCY LIMIT (-3DB POINT): 60 Hz

USABLE LOW FREQUENCY LIMIT (-10DB POINT): 52 Hz

Internal power amplifiers (@120 VAC line):

Woofer - 1200 watts peak available power CONTINUOUS POWER: 550 watts @ less than 1% distortion

Tweeter - 150 watts peak available power CONTINUOUS POWER: 75 watts @ less than 1% distortion.

NOMINAL SENSITIVITY (1W @1M, SWEPT SINE INPUT IN ANECHOIC ENVIRONMENT):

100 dB (average)

MAXIMUM SOUND PRESSURE LEVEL: 131 dB music peak

NOMINAL RADIATION ANGLES: 100˚ horizontal by 15˚ vertical

TRANSDUCER COMPLEMENT: 12” Neodymium Dual Voice Coil Scorpion® woofer, Model SDC1288 and RD™2.6 with 4.75” long aluminum composite ribbon tweeter

BOX TUNING FREQUENCY (FBOX): 61 Hz

ELECTROACOUSTIC CROSSOVER

FREQUENCY: 2,000 Hz

CROSSOVER TYPE: Internal Electronic two-way crossover with driver EQ, level matching, bass boost and subsonic filtering.

CROSSOVER SLOPES: 24 dB/octave (fourth order) low pass, 24dB/octave

(fourth order) high pass, both with staggered poles and driver EQ. Unit has horn spatially aligned with woofer, so there is no need for phase alignment or time delay of the signals.

ELECTRONIC INPUT IMPEDANCE (NOMINAL):

10 k ohms unbalanced

20 k ohms balanced line level

2.4 k ohms balanced mic level

Impulse® 12D

SPECIFICATIONS

INPUT CONNECTIONS: Input 1: One combo female XLR/ 1/4” phone jack providing balanced operation, with switch-selectable mic- or line-level sensitivity.

One 3-conductor balanced Euro-style jack connector

Input 2: One combo female XLR/ 1/4” phone jack providing balanced operation, with switch-selectable mic- or line-level sensitivity.

Two RCA phono-type jacks, which are buffered and mixed to monophonic for a summed signal. These are NOT a stereo input, as the Impulse® 12D is a single full-range sound source.

OUTPUT CONNECTIONS: One male XLR balanced output, one ¼” TRS balanced phone-type jack, one 3-conductor balanced Euro-style jack connector.

CABINET MATERIAL: Injection-molded polypropylene with internal ribbing and bracing, and with textured finish. Molded material is dark gray, as is the metal grille. Available in a white version as well.

MOUNTING: Subwoofer pole-mounting or speaker stand via molded-in pole mount, flying via Versamount™70+, and 4 rubber feet for floor or stage use.

Dimensions: H x W x D

Front: 24.89” (63.2 cm) x 15.63” (39.7 cm) x 15.38” (39.1 cm)

Rear: H x W 23.13” (58.8 cm) x 7.50” (19.1 cm), 13.50” (34.3 cm) at second angle break

WEIGHT: 39 lbs. (17.7 kg)

ELECTRONICS AND AMPLIFIER SPECIFICATIONS:

ELECTRONIC INPUT IMPEDANCE (NOMINAL): Balanced inputs: 20 k ohms line level sensitivity selected, 2.4 k ohms mic level sensitivity selected

15

MIC SWITCH SENSITIVITY INCREASE: 30 dB

INFRASONIC FILTER PROTECTION: 36 dB/ octave roll-off

WOOFER DRIVE MODE: Servo-controlled feedback for lower distortion and precise signal tracking.

PUSH-BUTTONEQ MODES OF DYNAQ:

Flat frequency response

Filtered roll-off of high and low frequencies (Speech Mode)

Dynamic boost to high frequencies (Contour)

Dynamic boost to both high and low frequencies, (Fletcher-Munson type compensation, Contour and Bass enhancer)

SLEEP MODE: When Sleep Switch is engaged, unit will shut down the electronics after 16 minutes of no signal input. Unit will come back on within 3-5 seconds of an applied signal.

NOMINAL AMPLIFIER FREQUENCY RESPONSE: +0, -1 dB from 10 Hz to 20 kHz

HUM AND NOISE: Greater than 90 dB below rated power

DDT DYNAMIC RANGE: Greater than 22 dB

THD AND IM: Typically less than 0.1 %

DAMPING FACTOR: Greater than 100 @ 1000 Hz, 8 ohms

POWER REQUIREMENTS OF PEAVEY IMPULSE® 12D SYSTEM (DOMESTIC): Nominal 700 watts, 120 VAC, 60 Hz