Manuals / Pelco / Computer Equipment / Switch

Pelco 100BASE-TX, 100BASE-FX manual Mounting the FX82052 Module Using the Wall Clip

Models: 100BASE-TX 100BASE-FX

1 40

Page 19

Mounting the FX82052 Module Using the Wall Clip

NOTE: Before mounting the FX82052 module to a wall, ensure that there is adequate space at both ends for viewing the front-panel LEDs and for making the various rear-panel cable connections.

To attach the FX82052 module to a wall using the supplied wall clip, refer to Figure 8 and do the following:

1.Using the two vertical or horizontal wall-mounting holes, attach the wall clip to a wall using two screws (not provided).

2.Slide the module into the clip until the two holes on the bottom of the module align with the two holes on the lower flange of the clip.

3.Attach the module to the clip using the two Phillips pan head screws provided for the clip.

UPPER

FLANGE

VERTICAL

MOUNTING HOLE (2)

HORIZONTAL

MOUNTING HOLE (2)

SCREW, PHILLIPS	LOWER
SCREW, PHILLIPS	FLANGE
PAN HEAD WITH	WALL CLIP
PAN HEAD WITH
LOCK WASHER (2)

Figure 8. Mounting the FX82052 Module Using the Wall Clip

C2607M (2/07)

Page 19

Image 19

Pelco 100BASE-TX, 100BASE-FX manual Mounting the FX82052 Module Using the Wall Clip

Contents

I N S T A L L A T I O N C2607M 2/07Ethernet Switch FX82052 UnmanagedList of Illustrations Contents7 FX Mode Switch 15 RJ-45 MDI/MDI-X Connector PinoutsList of Tables A TX Mode Switch Settings B FX Mode Switch SettingsImportant Safety Instructions RISK OF ELECTRIC SHOCK DO NOT OPEN RADIO AND TELEVISION INTERFERENCE Regulatory NoticesDESCRIPTION Product OverviewFIBER ONE FIBER REDUNDANTTWO FIBERS REDUNDANT Features of the FX82052 Ethernet switch include the following Single-Mode Models† OPTIONAL ACCESSORIESMODELS FX82052, -2 MODELS Multimode ModelsFRONT PANEL ó Power LED Pelco badgeï 100BASE-FX Status LED Per fiber port A and B REAR PANEL ï 10BASE-T/100BASE-TX Ports 1-5, RJ-45 connectorsFX82052 REAR PANEL, -2 MODELS FX82052 REAR PANEL, -4 MODELS ï 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectorsPACKAGE CONTENTS InstallationSETTING 10BASE-T/100BASE-TX PORT MODES OF OPERATION Autonegotiation is enabled by default 10BASE-T/100BASE-TX Modes of Operation SETTING FIBER FAILOVER MODEFX Mode Mode of OperationSwitch Position MOUNTING THE FX82052 MODULE INTO A RACK MOUNTINGMOUNTING THE FX82052 MODULE TO A WALL Mounting the FX82052 Module Using the Wall Clip CONNECTIONS 10BASE-T/100BASE-TX connections Power connectionFiber connections FIBER LINK FX MODE POSITION FIBER PORT A IS PRIMARY FIBER PORT B IS SECONDARYFX MODE POSITION FIBER PORT B IS PRIMARY FIBER PORT A IS SECONDARY PRIMARYC2607M 2/07 FX MODE POSITION FIBER PORTS A AND B ARE INDEPENDENT FX MODE POSITIONFIBER PORTS A AND B ARE INDEPENDENT FX MODE POSITION FIBER PORTS A AND B ARE INDEPENDENTTWO FIBERS FIBER PORT A IS PRIMARYC2607M 2/07 FIBER PORT B IS SECONDARYC2607M 2/07 FX MODE POSITION FIBER PORTS A AND B ARE INDEPENDENT FX MODE POSITIONFIBER PORTS A AND B ARE INDEPENDENT FX MODE POSITION FIBER PORTS A AND B ARE INDEPENDENTPossible Cause TroubleshootingPower LED Pelco badge MeaningCorrective Action Fiber Failover Mode onFiber Failover Mode LED Meaningport is not detected Laser fault on local moduleMeaning Corrective ActionCorrective Action Optic Fault LEDMeaning Possible CausePossible Cause RJ-45 10BASE-T/100BASE-TX Port Status LED - Left Link/ActivityModes of Operation on MeaningModes of Operation on MeaningPossible Cause Corrective ActionCorrective Action RJ-45 10BASE-T/100BASE-TX Port Status LED - Right Duplex/CollisionMeaning Possible CauseModes of Operation on MeaningPossible Cause Corrective ActionPossible Cause Indicator ColorIf 10BASE-T half-duplex operation is desired, no action is required. If 10BASE-T half- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 14 for information MeaningMECHANICAL SpecificationsPERFORMANCE GENERALOptical OPTICAL POWER BUDGET AND MAXIMUM TRANSMISSION DISTANCEFX82052, -2 Models Wavelengthof Fibers FX82052, -4 ModelsTransmit/Receive NumberMDI-X Appendix. RJ-45 Connector PinoutsRETURNS PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTY REVISION HISTORYTel 1-559/292-1981 Fax 1-559/348-1120 ISO9001Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel 800/289-9100 Fax 800/289-9150 International