Pelco es3012 8, 9, 10

Pelco Manual C306M-K (4/05) 11

8Turn on the power. If the red LED lights, turn off the power and proceed to the next

step. If the red LED does not light, refer to the

Troubleshooting

section.

9Plug the male Esprit system connector, located on the bottom of the pan and tilt, into

the female Esprit system connector located on the transformer module. Align the pan

and tilt part number with the alignment label of the base and then attach the pan and

tilt to the base with three 1/4-20 nuts and washers (supplied).

10 Set the receiver address and system baud rate by configuring DIP switches SW1 and

SW2.

To set the DIP switches:

a. Remove the plug from the left cover of the pan and tilt. It is not necessary to re-

move the pan and tilt cover.

b. Set the baud rate (SW1) and receiver address (SW2). For switch settings refer to

the labels located on the inside lid of the housing or Tables A and B in the

Appendix

.

c. Replace the plug.

NOTE:

Switch settings

have no effect on Coaxitron

control signals. The Esprit

will sense and automatically

select input from Coaxitron

control signals in either

standard or extended mode.

PART

NUMBER

ALIGNMENT

LABEL

MALE SYSTEM

CONNECTOR

FEMALE

SYSTEM

CONNECTOR

Contents

Main Page Pelco Manual C306M-K (4/05) 3 CONTENTS Page Pelco Manual C306M-K (4/05) 5 IMPORTANT SAFETY INSTRUCTIONS 6 Pelco Manual C306M-K (4/05) DESCRIPTION MODELS INSTALLATION CAMERA AND LENS INSTALLATION Pan and Tilt Installation A B C 3 4 5 PAN AND TILT INSTALLATION 1 2 3 The illustrations show the ES3012 Esprit mounted to an EWM wall mount. 4 5 6 7 8 9 10 Page HOW TO REINSTALL THE PAN AND TILT COVER OPERATION POWER-UP DISPLAY Operating Notes Programming Power-Up Mode in the Programming PAN, SCAN, AND TILT SPEEDS LENS FUNCTIONS PRESET FUNCTIONS RANDOM, FRAME, AND AUTO SCANNING ZONES PROGRAMMING ESPRIT MENUS PRESETS ACCESSING MAIN MENU (PRESET 95) if this is your first time entering this mode AZ/EL Az/El display is not available while you are AZ/EL LINE Az/El display is not available while you are AZIMUTH ZERO DIRECTION For direction to be accurate, the azimuth zero must be set to magnetic north. Direction display is not available while you are programmming or running a DIRECTION LINE Direction display is not available while you are DISPLAY DURATION LIMIT STOPS TURNING LIMIT STOPS ON OR OFF PROGRAMMING LIMIT STOPS Manual Limit Stops Scan Limit Stops PAN/SCAN SPEED PARK TIME NOTE: CAUTION: PATTERN LENGTH POWER-UP MODE SPEED PROFILE ZONES ZONE BLANK 30 Pelco Manual C306M-K (4/05) TROUBLESHOOTING MAINTENANCE Troubleshooting Warranty and Return Information 32 Pelco Manual C306M-K (4/05) APPENDIX Esprit will sense and automatically select input from Coaxitron Table A. Switch Settings for SW1 NOTES: Pelco Manual C306M-K (4/05) 33 Table B. Switch Settings for SW2 (Continued on next page) NOTE: 34 Pelco Manual C306M-K (4/05) Table B. Switch Settings for SW2 (continued) (Continued on next page) Pelco Manual C306M-K (4/05) 35 Table B. Switch Settings for SW2 (continued) SPECIFICATIONS (Design and product specifications subject to change without notice.) Pelco Manual C306M-K (4/05) 37 Figure 1. Esprit ES3012 System Dimensions Drawing REGULATORY NOTICES REVISION HISTORY Product Warranty and Return Information. section. In March, removed wiper material from Troubleshooting Trouble- shooting