C. Fold down top flap of water resistive barrier (6C). | 6C | |
| ||
D. Apply flashing tape to diagonal cuts. Cut pieces of |
| |
flashing tape at least 1" longer than the diagonal cuts |
| |
in the water resistive barrier. Apply the tape covering | 6D | |
the entire diagonal cut in the water resistive barrier | ||
| ||
at both upper corners of the window. | 6D |
Note: Be sure to overlap the top corners (6D).
7 INTERIOR SEAL
Caution: Ensure use of low pressure polyurethane window and door insulating foam and strictly follow the foam
manufacturer’s recommendations for application. Use of high pressure foams
or improper application of the foam may cause the window frame to bow and 7A hinder operation.
A. Apply insulating foam sealant. From the interior, insert the | Interior |
| |
NOZZLE OFLTHE APPLICATOR APPROXIMATELY EDEEP INTOTHEDSPACEP |
|
between the window and the rough opening and apply a 1" |
|
deep bead of foam. This will allow room for expansion of the |
|
FOAM AND WILLNMINIMIZEESQUEEZEEOUT )FFUSINGSFOAM OTHER THANM |
|
'REATA3TUFF 7INDOWWANDA$OORO)NSULATINGA&OAMA3EALANT BYY |
|
the Dow chemical Company, allow the foam to cure completely |
|
USUALLY TOL HOURS TBEFOREEPROCEEDING TOITHEGNEXT STEP |
|
Note: DO NOT completely fill the space from the back of |
|
the fin to the interior face of the opening. |
|
B. Check window operation (vent units only) by opening and |
|
closing the window. |
|
Note: If the window does not operate correctly, check to make sure it is still plumb, level, | |
square and that the sides are not bowed. If adjustments are required, remove the foam with | |
a serrated knife. Adjust the shims, and reapply the insulating foam sealant. |
8 SEALING THE WINDOW TO THE EXTERIOR WALL CLADDING
When applying siding, brick veneer or other exterior finish material, leave adequate space between the window frame and the material for sealant. Refer to the illustration that corresponds to your finish material.
Note: The sealant details shown are standard recommendations from the sealant industry. Contact your sealant supplier for recommendations and instructions for these and any other applications.
BRICK VENEER |
|
| VINYL/STEEL |
|
| |
|
|
| SIDING |
|
| |
|
|
|
|
| STUCCO | |
| Backer Rod and |
| Backer Rod and |
| ||
| Sealant typical |
|
| Sealant typical |
| |
Insulating | 3/8" Clearance | Insulating | 3/8" Clearance | Insulating | ||
Accessory Groove | Accessory Groove | |||||
Foam | Foam |
| ||||
| Perimeter Sealant | Foam | ||||
| Perimeter Sealant |
|
|
| ||
|
|
| must extend to |
| ||
| must extend to |
|
|
| ||
|
|
| room side of |
| ||
| room side of |
|
|
| ||
|
|
| Accessory Groove. |
| ||
| Accessory Groove. |
|
|
| ||
|
|
|
|
|
| 3/8” |
| 3/8" | |
| 3/8" |
| ||
|
|
| ||
| WOOD SIDING |
|
| |
| WITH TRIM | WOOD |
| |
1/2" | 1/2" | 1/2" | ||
SIDING | ||||
Min. | Min. |
| Min. | |
| Sealant typical |
|
|
| 3/8" Clearance |
| Sealant typical | |
Insulating |
|
| ||
Accessory Groove |
| 1/8" Clearance | ||
Foam | Insulating | |||
| ||||
| Perimeter Sealant |
| ||
| Foam |
| ||
| must extend to | Accessory | ||
|
| |||
| room side of |
| Groove | |
| Accessory Groove. |
|
| |
| 3/8" |
|
| |
|
|
| 1/8" |
Backer Rod and
Sealant typical
3/8" Clearance
Accessory Groove
Perimeter Sealant
must extend to
room side of
Accessory Groove.
1/2" Min.