![](/images/new-backgrounds/1027403/274035x1.webp)
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" |
| ||
longer than the opening width. Apply at the bottom of the |
| ||
| £ | ||
OPENINGNAS SHOWN % SO IT OVERHANGSA TOSTHEEXTERIOR |
| ||
Note: The tape is cut 12" longer than the width so that it will |
| ||
extend 6" up each side of the opening. |
| ||
|
| ||
F. Tab the sill flashing tape and fold. Cut 1" wide tabs at each |
| ||
|
| ||
CORNER FROM EACHESIDE OF CORNER E& F&OLDLTAPE TOATHEE |
|
| |
EXTERIOR AND PRESSSlRMLYlTO ADHEREEIT TOTTHETWATERTRESISTIVEEBARRIER |
| £ | |
' Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer |
| ||
THAN THE OPENING WIDTHE!PPLY ATYTHEABOTTOMHOVERLAPPINGPTAPE | |||
|
| ||
BYYAT LEAST $/S./44ALLOWWTHETTAPE TOTEXTEND PASTOTHEEINTERIOR |
|
| |
FACE OFETHEOFRAMINGH' |
| £ | |
| |||
|
| ||
piece of flashing tape. The flashing tape should come to within 1" |
|
| |
of the interior face of the framing. |
|
| |
Note: The flashing tape may not fully cover the framing |
|
| |
members. When using the optional fin at the bottom of the door, |
| ||
do not install the aluminum sill support or wood blocking until |
|
| |
after the doors have been installed in the rough opening. |
|
| |
( Attach the aluminum sill support or wood blocking to the |
| £ | |
EXTERIOR OFITHERBOXXPLATELTO SUPPORTTTHETEDGE OFETHEGDOOR SILL |
|
| |
Place the sill support flush with the subfloor. |
|
| |
2 SETTING AND FASTENING THE DOOR |
|
| |
A. Remove plastic wrap and cardboard packaging from door. DO |
|
| |
NOT remove plastic shipping spacers. The shipping spacers will help |
|
| |
keep the door square during installation. DO NOT unlock or open the |
|
| |
door until it is fully fastened. |
| Ó | |
Note: If screens, grilles or hardware are removed from the door at |
|
| |
this time, label them and store them in a protected area. |
|
| |
B. Fold out installation fin to 90°. Be careful not to remove or tear the |
|
| |
lN CORNERS |
|
| |
Note: If the fin is not at 90°, the door will not line up correctly on |
|
| |
the interior. If using the optional fin at the sill, apply the fin and fin |
| Ó | |
corners, then proceed to Step D. Sealant lines from Step C are not |
|
| |
required when using the optional fin at the sill. |
|
| |
C. Place three 3/8" beads of sealant. 4HEHlRST BEADSSHOULD BEA |
|
| |
APPROXIMATELY LFROM THE EXTERIOREOF THE ROUGH OPENINGPTHENSECOND |
|
| |
bead should be placed so it is under the wood interior threshold of the |
|
| |
door. Placement will vary depending on wall thickness and door |
|
| |
type. Place a third bead of sealant in the groove of the sill support | Ó | &YUFSJPS | |
OR FROM THE EXTERIOREEDGE OFRTHEOWOOD BLOCKING | |||
| |||
TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE |
|
| |
FOLLOWING STEPS. |
|
| |
D. Insert the door from the exterior of the building. |
|
| |
DO NOT slide the bottom of the door into the opening. Sliding |
|
| |
will damage the sealant lines. Place the bottom of the door at the |
|
| |
bottom of the opening, then tilt the top into position. Center |
|
| |
the door between the sides of the opening to allow clearance for |
|
| |
SHIMMINGMANDNINSERTTONEOROOlNGlNAIL INNTHEIlRST HOLE FROM THE |
|
| |
CORNER ONEEACH END OFETHECTOP NAILING lNF4HESEEAREEUSED TOEHOLDD |
|
| |
the door in place while shimming it plumb and square. |
|
|