SECTION V.

RELAMPING INSTRUCTIONS

 

 

WARNING

 

Risk of electric shock. Disconnect power before servicing this unit. Failure to disconnect power

 

can result in death or severe personal injury.

1.

It is desirable to reduce the water level to the lower edge of the flow director. This makes bulb

 

assembly replacement easier, but it is not mandatory.

2.Remove power from the unit by taking the power cord’s 3-prong plug and disconnecting it from its electrical outlet, or in the case of a hard-wired application, by turning the respective circuit breaker to the OFF position.

3.

Remove the snap-on cord cap by inserting a slotted

 

screw driver into the access hole as illustrated in

 

Figure 20 and prying upwards.

4.

Disconnect both wire connectors and put the snap-on

 

cord cap aside in a dry location and remove the bulb

 

assembly nut.

5.

At this point you should have the new replacement

 

bulb assembly accessible and confirm that the red

 

cap/plug is pressed firmly into the bulb assembly to

 

prevent water from entering the bulb assembly.

6.

If you were able to lower the water level as suggested

 

in step 1, then simply remove the old bulb assembly

 

by pulling on the flow director while pushing the bulb

 

assembly from the outside of the pool. If you were

 

unable to lower the water level, follow these

 

instructions: push the bulb assembly out from the

Sheet Metal Screw

Side of

Pool

Support

Pool Wall

Cable Clamp to hold wire tight against the wall.

Figure 18.

outside of the pool, keeping the back of the fitting

covered with a folded rag in the palm of your hand to

prevent water loss from the rear of the fitting body; see

Figure 4. Pull the flow director and bulb.

7. Take the new replacement bulb assembly with the red

cap/plug in place and insert the bulb assembly

through the flow director. Note the aligning keyway

on the bulb assembly as shown in Figure 8. The

keyway must point in the same direction as the top

key on the fitting body.

Now, from inside the pool, push the bulb assembly

with the flow director into the fitting body until both

are nearly flush against the inside pool wall. You can

now remove your hand and the fitting should again be

sealed.

Pool

Pool Wall

Figure 19.

Figure 20.

REV. F 1-6-05

9

P/N 98748000

Page 8 Page 10
Page 9
Image 9
Pentair Quasar owner manual Section Relamping Instructions, Can result in death or severe personal injury
Page 8 Page 10

Quasar specifications

Pentair Quasar is an innovative pool and spa filtration system designed to enhance water quality while providing exceptional energy efficiency and ease of use. Known for its advanced engineering and robust features, the Quasar series stands out in the competitive world of pool maintenance.

One of the key features of the Pentair Quasar is its advanced filtration technology, which integrates multi-layer filtration media to effectively capture both large debris and microscopic particles. This results in exceptionally clean water, ensuring that pool owners can enjoy crystal-clear swimming conditions. The multi-layer system minimizes the need for frequent filter changes, thus significantly reducing operational costs and environmental impact.

The Quasar utilizes cutting-edge pump technology, designed to operate efficiently at varying flow rates. This dynamic performance allows for optimal circulation without wasting energy, catering to different pool sizes and requirements. The variable-speed pumps are engineered to deliver silent operation while achieving significant energy savings compared to traditional single-speed pumps. This aligns well with the growing trend towards sustainability in pool management.

Another standout characteristic is its user-friendly control system, which features intuitive touchscreen interfaces that allow for easy adjustments to temperature, filtration schedules, and maintenance alerts. The user-centric design ensures that operators, regardless of experience level, can manage water quality effectively. Moreover, this system can seamlessly integrate with modern smart home technologies, allowing users to monitor and control their pool environment remotely via mobile applications.

The Pentair Quasar also emphasizes durability and reliability. Constructed from high-quality materials resistant to corrosion and UV damage, the system is built to withstand the rigors of outdoor environments. Maintenance is simplified further by design elements that facilitate easy access to internal components, making routine servicing more convenient.

In addition, the Quasar series features advanced water sanitization technologies, including options for salt chlorination systems which promote a more natural swimming experience, free from harsh chemicals. This enhances swimmer comfort while maintaining the highest water sanitation standards.

In summary, the Pentair Quasar represents a leap forward in pool filtration technology. With its multi-layer filtering capabilities, energy-efficient pumps, intuitive control systems, and enhanced durability, it offers an optimal solution for homeowners looking to maintain pristine pool conditions with minimal effort and environmental impact. The Quasar is a testament to Pentair's commitment to innovation in water technology, making it a preferred choice for discerning pool enthusiasts.
Top Page Image Contents