Philips 55PFL5907, 46PFL5907 Manually enter your Ssid, Auto Router Enter Key, None, Back

Wireless network setting

This menu is displayed only when you set Wireless in

Network selection. In order to use a wireless network, you must set up a connection to the AP (e.g. wireless router).

3 Use ▲▼ to select Wireless network setting, then press OK.

Auto

Search for wireless networks automatically and select the SSID from the list.

4 Use ▲▼ to select Auto, then press OK.

5 The list of wireless networks will be displayed.

Use ▲▼ to select the appropriate the SSID, then press OK.

Auto	Router 1	Enter Key
Manually enter your S	Router 2	Select
	Router 3	Enter Key
	Router 4	Select

•If you select the SSID with ,WEP*2 /WPA /WPA2 Key entry screen will appear.

Enter the WEP*2 / WPA /WPA2 key of the selected wireless network using ▲▼◄►, then press OK.

•If you select the SSID has a WPS, the WPS setting screen will appear.

Use ▲▼◄► to select a setting, then press OK.

	Select this setting if your router has a WPS
	button. Start scanning for wireless networks on
Easy connect	the TV after pressing the WPS button on your
	router. If connection test fails, try Easy connect
	again.*1
	If it fails then refer to the router’s manual for
	more details.
	Select this setting if your router has a WPS but
WPS code	does not have a WPS button. Enter the 8-digit
	WPS PIN code shown on your TV in the router
	settings menu via PC before Connect is selected.
	If your wireless network with authentication
	setting (WEP*2,WPA-PSK or WPA2-PSK),
Manual	WEP*2 /WPA /WPA2 Key entry screen will
	appear. Enter the WEP*2 /WPA /WPA2 key of
	the selected wireless network using ▲▼◄►,
	then press OK.

*1 WPS (Easy Connect) cannot be used when the security protocol is set to WEP. Change the Access Point’s security mode from WEP to WPA or WPA2 (recommended).

*2 WEP is not recommended to be used due to its Major security flaws. Change the Security protocol on the wireless router to WPA or WPA2 (recommended) mode.

Confirmation message will appear. Select OK to complete the settings.

Note

•For a wireless network with authentication setting, key icon appears to the right hand of the SSID.

•Signal icon shows the strength of the signal.

•WEP*2 / WPA key appears as asterisks on the confirmation screen.

•The wireless LAN supports following specifications.

–	Wireless standards	: IEEE 802.11 b/g/n
–	Frequency spectrum	: 2.4GHz
– Security protocol		: WEP*2 /WPA /WPA2

41 English

Manually enter your SSID

Set up the connection to the AP (e.g. wireless router) manually by entering the SSID.

4 Use ▲▼ to select Manually enter your SSID, then press OK.

• AP(e.g. wireless router) SSID entry screen will appear. Enter the SSID using ▲▼◄►, then press OK.

5 Use ▲▼ to select the authentication setting of the selected wireless network.

•For a wireless network with authentication setting, select the authentication setting, according to the security type of the wireless network.

Select security type for	None
"Router 1"
	WEP
	WPA-PSK
	WPA2-PSK
Back
None	Set the authentication setting to None.
WEP*2	Set the authentication setting to WEP.*2
WPA-PSK	Set the authentication setting to WPA-PSK.
WPA2-PSK	Set the authentication setting to WPA2-PSK.

•For a wireless network without authentication setting, select None.

•If you select WEP*2, WPA-PSK or WPA2-PSK,WEP*2 / WPA /WPA2 Key entry screen will appear.

Enter the WEP*2 / WPA /WPA2 key of the selected wireless network using ▲▼◄►, then press OK.

•Confirmation message will appear. Select Yes to complete the settings.

*2 WEP is not recommended to be used due to its Major security flaws. Change the Security protocol on the wireless router to WPA or WPA2 (recommended) mode.

Continued on next page.