BDL5551EL
By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below:
|
| PIP |
|
| POP |
|
| PBP aspect |
| PBP full |
| Off |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The resolutions in the PIP and POP modes are configured as follows:
PIP SIZE | {Small} | : 320 x 240 pixels |
| {Medium} | : 480 x 320 pixels |
| {Large} : 640 x 480 pixels | |
POP SIZE: 474 x 355 pixels | ||
NOTE: | The images displayed in the sub picture always fit the PIP | |
| sizes shown above irrespective of the aspect ratio of the input | |
| image. |
|
4.2.5. Configuration1 menu
Panel saving
Choose to enable the panel saving functions and thus reduce the risk of “image persistence” or
• {Cooling Fan} - Select {On} to turn on the cooling fan all the |
time. Select {Auto} to turn on/off the cooling fan according to the |
display’s temperature. |
NOTES: |
• The default {Auto} option will start running the cooling fan |
if the temperature of 60°C (140°F) is reached, and will keep |
running for 30 minutes after cooling down to the temperature |
of 58°C (137°F). |
• A |
the temperature reaches 79°C (174°F). All key functions except |
[Power] key will then be disabled. |
• Once the temperature reaches 80°C (176°F), the display power |
will be shut down automatically. |
• {Brightness} - Select {On} and the image brightness will be reduced |
to an appropriate level.The Brightness setting in the Picture menu |
Picture
Screen
Audio
PIP
Configuration1
Configuration2
Advanced option
Switch on state Auto adjust Power save Language Panel saving Color system Network control port Network settings Configuration reset Factory reset
will be unavailable when selected. |
• {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds |
/ {Off}) for the display to slightly expand the image size and shift the |
position of pixels in four directions (up, down, left, or right). |
Color system
Selects the Color System depending on your input video format.
The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} /
NOTE: This item is functional for VIDEO input only.
Network control port
Select the network control port.
Choose from: {RS232} / {LAN(RJ45)} / {Card OPS RS232}.
Switch on state
Select the display status used for the next time you connect the power cord.
•{Power off} - The display will remain off when the power cord is connected to a wall outlet.
•{Forced on} - The display will turn on when the power cord is connected to a wall outlet.
•{Last status} - The display will return to the previous power status (on/off/standby) when removing and replacing the power cord.
Auto adjust
Use this function to automatically optimize the display of VGA input image.
NOTE: This item is functional for VGA input only.
Power save
Use this setting to reduce the power automatically.
•{RGB} - Select {On} to let the display enter APM mode when no signal is detected from the HDMI Graphic mode, HDMI,
•{VIDEO} - Select {On} to enter power saving mode when no signal is detected from the HDMI Video mode or YPbPr inputs after three successive cycles.
Language
Select the language used in the OSD menu.
The options are: {
} / {
} / {
} / {
} / {
} /
{
} / {
} / {
} / {
} / {
} .
NOTES:
•If {LAN(RJ45)} is selected, then {RS232} will not be activated, even if a cable is attached, and vice versa.
•The option {Card OPS RS232} is functional after connected with your OPS device.
Network settings
Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display.
Network settings
Network host name |
| 9 |
| 0 | Z | L |
|
|
|
DHCP |
|
|
|
| Disable |
|
|
| |
IP address | 172 | - | 16 | - | 0 | - | 1 | ||
Subnet mask | 255 | - | 255 | - | 0 | - | 0 | ||
Default gateway | 0 |
| - | 0 | - | 0 | - | 0 | |
Login user name |
| a | d | m i | n |
|
|
| |
Login password | 0 |
| 0 | 0 |
| 0 |
|
| |
| [ SET ] |
|
|
|
|
|
| ||
change [SET] in STORE
•DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted to enter the following values manually. When finished, press [SET] button to store and save the chosen values.
19
