SETUPS

If you select “Manual”, follow the following instruction to set the IP address and DNS.

4-a) IP address setting screen will appear. Enter IP address, subnet mask and default gateway with cursor buttons and number buttons.

IP Address Setting

IP Address

Subnet Mask

Default Gateway

Clear

OK

•Enter the IP address number after checking the specifications of your router.

•If the IP address number is unknown, check the IP address number of other devices. (e.g. PC connected via LAN cable) and assign a different number from those of other devices.

After you enter all correctly, press [OK] to go to the DNS setting screen.

4-b) DNS setting screen will appear. Enter primary DNS and secondary DNS with cursor buttons and number buttons.

DNS Setting

Primary DNS

Secondary DNS

Clear

OK

•Enter the numbers instructed by your Internet provider.

•If the number is unknown, check the number of other devices (e.g. PC connected via LAN cable) and assign the same number.

4-c) After you enter all correctly, press [OK].

•Confirmation message will appear. Select “Yes” to complete the settings.

IP Address

***.***.***.***

Subnet Mask

***.***.***.***

Default Gateway

***.***.***.***

Primary DNS

***.***.***.***

Secondary DNS

***.***.***.***

 

Is Setting OK?

 

Yes

 

No

5)Press [BACK U] to go back to the previous screen, or press [HOME ] to go back to the home menu.

Note

•The range of input number is between 0 and 255.

•If you enter a number larger than 255, the number will automatically be 255.

•The manually entered number will be saved even if you change the setting to “Auto(DHCP)”.

•When you enter a wrong number, press [RED] to cancel. (the number will be back to “0”.)

•If you want to enter 1 or 2 digit number in one cell, press [B] to move on to the next cell.

•If the entered IP address or the default gateway or primary DNS number is same as the default setting, IP address setting will be set to “Auto(DHCP)”. (The manually entered number will be saved).

•When IP address setting is set to “Manual”, the setting of DNS setting will automatically be “Manual” and when IP address setting is set to “Auto(DHCP)”, you can set either “Auto(DHCP)” or “Manual” for DNS setting.

•Proxy Setting

1)Follow steps 1) to 4) in “Connection Test” on page 43.

2)Use [K / L] to highlight “Enable(Custom)”, then press [OK].

3)Use [K / L] to highlight “Proxy Setting”, then press [OK].

4)Use [K / L] to highlight the desired setting, then press [OK].

•For default settings, select “Do Not Use”.

•If you need to change the proxy setting as instructed by your Internet service provider to set the designated proxy address and port, select “Use”.

If you select “Use”, follow the following instructions to set the proxy address and proxy port.

4-a) Proxy address setting screen will appear. Enter proxy address.

• The keyboard screen will appear.

Proxy Setting

Proxy Address

 

 

 

 

 

 

 

 

 

 

********

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

 

7

8

9

0

 

 

 

 

a

b

c

d

e

f

 

g

h

i

j

 

 

 

 

k

l

m

n

o

p

 

q

r

s

t

 

 

 

 

u

v

w

x

y

z

.

-

_

OK

 

 

 

Clear

 

 

 

All Clear

 

 

 

a/A/@

OK

[K / L / s / B] : Move the highlight.

[the Number buttons] : Enter number.

[OK] : Enter the highlighted number/word. *[RED] : Clear the entered number or word.

[GREEN] : Clear all the entered numbers or words.

[BLUE] : Switch between abc ? ABC ? @!? *[YELLOW] : Set the entered number or word.

* These buttons can be used in other network settings.

44 EN