Using the Remote Control
Installing the Batteries
To load the supplied batteries into the remote:
1 Remove the battery compartment door on the back of the remote.
2 Place the batteries
3 Reattach the battery compartment door.
Be sure to point the remote at the Remote Sensor window on the front of the television when using it to operate the television.
Remote Control Buttons
Select (CBL VCR DVD SAT AMP) and Backlight
Press this button to cycle across the accessory mode dial. Stop pressing when the mode you desire is lighted. The light will stay on for 2 seconds and then begin blinking to indicate the remote is in your desired mode. Once the mode is selected, you must press a button within 60 sec- onds for the remote to remain in the selected mode or it will default back to the TV mode. (See pages
Source
Press to display a list of source
Alternate Audio (SAP)
When you tune to a channel where SAP (Second Audio Program) is available, you can toggle between Main and SAP. If SAP is not available, only Main can be selected. (See page 42 in the Directions for Use manual.)
PixelPlus™ Demo
Press to activate the demo, which illustrates the benefits of Pixel Plus™. Press again to turn the demo off. Press and the TV screen will be divided in half displaying the Pixel Plus™ Demo. The left side will show the picture with Pixel Plus™ switched off. The right side of the screen will show the picture with Pixel Plus™ switched on. (See page 30 in the Directions for Use manual.)
OK
Press to activate or confirm menu choices.
Freeze Format
Pressing will apply one of the Freeze modes you set using the
Freeze mode stops action in the main screen. Sound will continue to be heard. Press again to resume nor- mal viewing.
Replay mode displays a few seconds of stored video in the PIP window.
Photo Finish mode displays six stored frames from the picture.
NOTE: Continuing to hold the Freeze Format button down will cycle the TV through the Freeze modes: Freeze, Replay, and Photo Finish.
VOL (Volume)
Press + or – to adjust the volume.
Mute
Press to interrupt or restore sound.
Information Plus+
Press to show information (when available) about the current channel, program, source, number or name, local time, CC availability, SAP availability, program ratings, display format, sound mode, and remaining length of a Sleeptimer setting.
Dual Screen/PIP (Picture-in-Picture)
Press to turn the PIP dual screen on or off. Continuing to hold the Dual Screen/PIP button down will cycle through the Dual Screen/PIP options. (See page 58 in the Directions for Use manual.)
3
Remote Control
(shown from the bottom)
1
®
® | ® |
®
HELPFUL HINT
When the batteries in your remote control run low, the remote control will send a “Battery low” command to the TV. The TV will then display a message on the screen reminding you to replace the batteries as soon as possible.
2
Press to turn the TV on or off.
NOTE: The TV is never powered off completely unless it is physically unplugged from the power source.
Surround Sound
Press to display a list of available sound modes. Choose from Incredible Surround™ and Dolby* Virtual settings. (See page 41 in the Directions for Use manual.)
VCR/DVD Functions
When the remote is in the VCR mode, these buttons will allow you start a recording (●), rewind a tape (), stop the playback of a tape (■), play a videotape (), or
Time Display
Press to display the current time on the TV screen.
CC (Closed Captioning)
Press to turn Closed Captioning off, on, or on during mute. (See page 47 in the Directions for Use manual.)
Cursor Up, Down, Right, Left
Use to navigate the
Additionally, use these buttons to pan the screen up or down to show any excluded parts of the picture. Left or right panning is possible with the Side input source when “Game” is selected as the type of source for the Side input. (See page 18 in the Directions for Use manual.) Also use with the Dual Screen/PIP feature to select a screen or reposition a PIP screen. (See page 58 in the Directions for Use manual.)
Menu On/Off
Press to display the TV’s
CH (Channel Selection)
Press to browse through the TV channels.
Digit (Number Buttons)
Press to directly access a specific TV channel. For a two- or
PP (AutoSurf™)
If you set the Surf control in the TV’s
Active Control™ Plus
NOTE: Active Control™ Plus is not available for use with the AV3, AV4, AV5, and AV6 input sources.
Press to toggle the options Off, Minimum, Medium, and Maximum. Maximum is the recommended option. See page 28 in the Directions for Use manual.
Picture Format
Press to display a list of available picture formats for showing video images in the traditional 4:3 proportions. Press this button repeatedly to select a picture format. Choose from Automatic, Super zoom, Panoramic, 4:3, Movie expand 14:9, Movie expand 16:9, 16:9 subtitle, and Wide screen. See pages
NOTES:
•With
•In Dual Screen mode, press the Picture Format button to switch between a full or 4:3 letterbox picture format.
Active Control, AutoSurf, Incredible Surround, and Pixel Plus are trademarks of Philips Consumer Electronics. Copyright 2003 Philips Consumer Electronics. All rights reserved.
*Manufactured under license from Dolby Laboratories. “Dolby” and the
6
