Philips DSR 300/00, DSR 310/00 6 General Viewing Function

18 GENERAL VIEWING FUNCTION

This section describes the basic functions available while

watching satellite TV or listening to satellite Radio. For general

menu navigation information, see Basics about menu navigation.

6.1 Receiver wake up

Your receiver is in standby.To wake it up, press any of the

following on the remote control:

- numerical keys,

- <P->/<P+>.

Note: the Standby button can only be used to switch the

receiver off.

6.2 Channel Information

Every time you change channels, programme information

appears on screen, displaying:

- The channel name and number in the current channel list.

- The current programme name.

- Icons indicating the channel properties, e.g. channel lock status.

- A bargraph indicating the start time of the current

programme,the start time of the next programme,and

the current progress.

While watching a channel, you can display the current

channel information at anytime by pressing <INFO> on the

remote control. Press <INFO> again to get more

information about the current programme.

Note: channel information is displayed for 3 seconds as per

default.This can be adjusted from the System Setting screen.

6.3 Channel selection

6.3.1 Using <P+/P-> or numeric keys

T

o switch channels, use <P+>/<P-> or the numeric keys of

the remote control.

English

6 General Viewing Function

icon description

alternate audio

language/format

current favourite list

maturity rating locked

scrambled channel

locked channel

subtitles presence

teletext presence

Doc_DSR300.qxd 29/11/04 13:19 Page 18

Contents

Main Safety instructions Meaning of symbols Quick installation guide AB TABLE OF CONTENTS Page 1 Introduction 2 Product description 2.1 Unpacking the product 2.2 Front panel Q W E R 2.3 Rear panel WI T Q E R U Y 10 REMOTE CONTROL 3 Remote control Page 4 Connecting your receiver Warning! 4.1 Connecting to a Satellite Antenna and a TV 4.2 Connecting to a TV and a VCR/DVD player using the SCART Support 4.3 Connecting to a Digital Amplifier/Home Theatre/HiFi system AB 5 First installation 5.1 Menu language and port selection 5.2 Channel scanning 5.3 Scanning failure 5.3.1 Antenna Setting 5.3.2 Signal test 6.1 Receiver wake up 6.2 Channel Information 6.3 Channel selection 6 General Viewing Function 6.3.2 Using the channel list 6.4 Channel lists 6.5 TV or Radio Mode selection 6.6 Volume & Audio Control 6.6.1 Volume control and Mute 6.6.2 Audio Control 6.7 Recording timers 6.7.1 To set a timer from the guide 6.7.2 To set or modify a timer from the Timer menu 6.7.3 To delete a running timer while watching digital TV or listening to digital radio 6.7.4 To delete a running timer set while the receiver was in standby 7 Menu 7.1 General information 7.1.1 Basics about menu navigation 7.1.2 Cancel/Store changes 7.2 Guide (Electronic Programme Guide) 7.3 Channel Manager 7.3.1 Channel Pool 7.3.2 Favourites 7.4 Parental Control 7.4.1 To enable Menu Lock 7.4.2 To set the Parental Rate 7.4.3 To change your receiver's Pin Code 7.5 Timer Manager 7.5.1 Recording timer 7.5.2 Reminder 7.5.3 Sleep timer 7.6 Setup menu 7.6.1 Time Setting 7.6.2 System Setting 7.6.3 Remote Control setting Page 7.7 Installation 7.7.1 Antenna Setting 7.7.2 Add Service 7.7.3 Signal Test 7.7.4 Product Identifier 7.7.5 Factory Default 7.7.6 Software update 34 MENU TREE 8 Menu tree Page 36 TROUBLESHOOTING 9 Troubleshooting Symptom Cause Remedy TROUBLESHOOTING 37 Symptom Cause Remedy