Manuals / Brands / TV and Video / Satellite TV System / Philips / TV and Video / Satellite TV System

Philips DSR 300/00, DSR 310/00 5.3.1 Antenna Setting, 5.3.2 Signal test

1 38

Download 38 pages, 7.33 Mb

5.3.1 Antenna Setting

- To continue, press <OK>.The Antenna Setting screen

appears to help you with the installation process and to

adjust your settings if needed.

- Choose a satellite for the applicable port and enter the

LNB type (universal by default) and LNB frequencies.You

can test the signal by pressing the <Green> key of the

remote control.

- Press <OK> to start scanning again. If the same failure

message appears after a while, refer to the

Troubleshooting chapter.

5.3.2 Signal test

You will not receive the signal from the satellite if your

antenna is not positioned correctly, even though you have

entered the correct values in the Antenna Set up menu.Your

receiver therefore provides precise Antenna Direction

information to help you direct your antenna toward a

satellite.

- Press the <Green> key of the remote control to access

the Signal Test screen. It indicates the strength of the

incoming satellite signal as well as the quality of reception.

- If both the signal strength and reception quality are

inadequate, you may need to change the direction in which

the antenna is pointing until the level becomes satisfactory.

- Press <OK> to start scanning again.

Note: if the same failure message appears after a while, refer to

the Troubleshooting chapter.

English

FIRST INSTALLATION 17

Doc_DSR300.qxd 29/11/04 13:19 Page 17

Contents

Main Safety instructions Meaning of symbols Quick installation guide AB TABLE OF CONTENTS Page 1 Introduction 2 Product description 2.1 Unpacking the product 2.2 Front panel Q W E R 2.3 Rear panel WI T Q E R U Y 10 REMOTE CONTROL 3 Remote control Page 4 Connecting your receiver Warning! 4.1 Connecting to a Satellite Antenna and a TV 4.2 Connecting to a TV and a VCR/DVD player using the SCART Support 4.3 Connecting to a Digital Amplifier/Home Theatre/HiFi system AB 5 First installation 5.1 Menu language and port selection 5.2 Channel scanning 5.3 Scanning failure 5.3.1 Antenna Setting 5.3.2 Signal test 6.1 Receiver wake up 6.2 Channel Information 6.3 Channel selection 6 General Viewing Function 6.3.2 Using the channel list 6.4 Channel lists 6.5 TV or Radio Mode selection 6.6 Volume & Audio Control 6.6.1 Volume control and Mute 6.6.2 Audio Control 6.7 Recording timers 6.7.1 To set a timer from the guide 6.7.2 To set or modify a timer from the Timer menu 6.7.3 To delete a running timer while watching digital TV or listening to digital radio 6.7.4 To delete a running timer set while the receiver was in standby 7 Menu 7.1 General information 7.1.1 Basics about menu navigation 7.1.2 Cancel/Store changes 7.2 Guide (Electronic Programme Guide) 7.3 Channel Manager 7.3.1 Channel Pool 7.3.2 Favourites 7.4 Parental Control 7.4.1 To enable Menu Lock 7.4.2 To set the Parental Rate 7.4.3 To change your receiver's Pin Code 7.5 Timer Manager 7.5.1 Recording timer 7.5.2 Reminder 7.5.3 Sleep timer 7.6 Setup menu 7.6.1 Time Setting 7.6.2 System Setting 7.6.3 Remote Control setting Page 7.7 Installation 7.7.1 Antenna Setting 7.7.2 Add Service 7.7.3 Signal Test 7.7.4 Product Identifier 7.7.5 Factory Default 7.7.6 Software update 34 MENU TREE 8 Menu tree Page 36 TROUBLESHOOTING 9 Troubleshooting Symptom Cause Remedy TROUBLESHOOTING 37 Symptom Cause Remedy