Philips DSR 300/00, DSR 310/00 6.7 Recording timers

6.6.2 Audio Control

- To access audio settings, select the Setup menu from the

main menu, then select System Setting.The System Setting

screen appears.

- Select Audio Output. Default Audio Output setting is Stereo.

- Select the desired value (Left, Right, Mono, or Stereo) and

press <OK> to save your changes and exit the screen.

6.6.3 Audio language

To select your preferred audio language:

- Select System Setting from the main menu.The System

Setting screen appears.

- Scroll to Audio Language, and then select the desired

language.

- Press <OK> to save your changes and exit the screen.

Note: if you want to change the audio language for a particular

programme, press <I-II> on the remote control to directly access

the audio language options available for this programme.

Available languages depend on the audio content transmitted.

6.6.4 Subtitles language

To select your preferred Subtitles language:

- Select System Setting from the main menu.The System

Setting screen appears.

- Scroll to Subtitle Language, and then select the desired

language.

- Press <OK> to save your changes and exit the screen.

Note: if you want to change the Subtitle language for a particular

programme, press < > on the remote control to directly access

the Subtitles language options available for this programme.

Available languages depend on the content transmitted.

6.7 Recording timers

Recording timers are used for VCR or DVD recordings.

6.7.1 To set a timer from the guide

- Select Guide from the main menu to access the Electronic

Programme Guide.

- Move to the desired programme using the arrow keys.

20 GENERAL VIEWING FUNCTION

English

Doc_DSR300.qxd 29/11/04 13:19 Page 20

Contents

Main Safety instructions Meaning of symbols Quick installation guide AB TABLE OF CONTENTS Page 1 Introduction 2 Product description 2.1 Unpacking the product 2.2 Front panel Q W E R 2.3 Rear panel WI T Q E R U Y 10 REMOTE CONTROL 3 Remote control Page 4 Connecting your receiver Warning! 4.1 Connecting to a Satellite Antenna and a TV 4.2 Connecting to a TV and a VCR/DVD player using the SCART Support 4.3 Connecting to a Digital Amplifier/Home Theatre/HiFi system AB 5 First installation 5.1 Menu language and port selection 5.2 Channel scanning 5.3 Scanning failure 5.3.1 Antenna Setting 5.3.2 Signal test 6.1 Receiver wake up 6.2 Channel Information 6.3 Channel selection 6 General Viewing Function 6.3.2 Using the channel list 6.4 Channel lists 6.5 TV or Radio Mode selection 6.6 Volume & Audio Control 6.6.1 Volume control and Mute 6.6.2 Audio Control 6.7 Recording timers 6.7.1 To set a timer from the guide 6.7.2 To set or modify a timer from the Timer menu 6.7.3 To delete a running timer while watching digital TV or listening to digital radio 6.7.4 To delete a running timer set while the receiver was in standby 7 Menu 7.1 General information 7.1.1 Basics about menu navigation 7.1.2 Cancel/Store changes 7.2 Guide (Electronic Programme Guide) 7.3 Channel Manager 7.3.1 Channel Pool 7.3.2 Favourites 7.4 Parental Control 7.4.1 To enable Menu Lock 7.4.2 To set the Parental Rate 7.4.3 To change your receiver's Pin Code 7.5 Timer Manager 7.5.1 Recording timer 7.5.2 Reminder 7.5.3 Sleep timer 7.6 Setup menu 7.6.1 Time Setting 7.6.2 System Setting 7.6.3 Remote Control setting Page 7.7 Installation 7.7.1 Antenna Setting 7.7.2 Add Service 7.7.3 Signal Test 7.7.4 Product Identifier 7.7.5 Factory Default 7.7.6 Software update 34 MENU TREE 8 Menu tree Page 36 TROUBLESHOOTING 9 Troubleshooting Symptom Cause Remedy TROUBLESHOOTING 37 Symptom Cause Remedy