Philips DVD962SA owner manual Speakers, X Y Z a

46 Speakers

The Player lets you adjust the speaker settings, volume balance, and delay time for your audio system. You only need to adjust the speaker settings if you used the Player’s MULTICHANNEL AUDIO OUT jacks to connect the Player to a six-channel Receiver (Dolby Digital or DTS) as shown on page 14.

1

Press SYSTEM MENU, then press ; to select V .

2

Press 9 repeatedly to select q , then press :.

3

Press 9 repeatedly to select Speakers, then press :.

V W X Y Z } a

1 2 1en off no off

DVD Only			Speakers
Front L & R			X
Center	s	c
	ss
Surround L			s
		S	s
Surround R
Sub Woofer
OK to exit		0dB L 4ms

4

Press 8 or 9 to select the speaker you want to adjust, then press :. You can select Front L & R (left and right), Center, Surround L (left), Surround R (right), or Sub Woofer. The speaker you selected will be highlighted in the illustration at the right of the screen.

5

Press : or ; to select B, z , or X. Then, press 8 or 9 to adjust the chosen setting. When you are finished, press OK to go back and select a different speaker. Repeat steps 4-5 until you are satisfied with all the speaker settings.

●Choose Bto increase or decrease the volume of the speaker.

● Choose z to adjust the frequency capabilities of your speakers. Select L (large) if the chosen speaker can handle low frequency signals below 120 Hz. Select S (small) if the speaker can not reproduce low fre- quency signals below 120 Hz. Select c (off) if you did not connect that speaker. Your choice will appear below the z bar at the bottom of the screen. See your speakers’ literature for details on speaker capability.

●Choose Xto adjust the speaker delay time. You can adjust the delay time for only the Center and Surround speakers.

If the surround speakers are about 150 centimeters nearer to the listening position than the front speakers, and the center speaker aligns with the front speakers, no adjustment is needed.

If your speaker setup is different, adjust the delay times. First, measure the distance, in centimeters, from the front speaker to the listening position and from the surround speaker to the listening position. Subtract the sur- round distance from the front distance, then divide by 30. The result is the

Surround speaker delay time in milliseconds.

You may choose 0 ms, 5 ms, 10 ms, or 15 ms in the Xcolumn for

Surround L and Surround R. Press 8 or 9 to choose the delay time in the Xcolumn for Surround L and Surround R that is closest to the delay time you calculated in milliseconds (ms).

Or, if the Center speaker is closest to the listening position, measure the distance (in centimeters) between the Front and Center speakers, then divide by 30. The result is the required Center speaker delay time in mil-

liseconds. Press 8 or 9 to select this delay time in milliseconds (ms) in the Xcolumn for Center. You may choose 1-5 ms.

6

Press SYSTEM MENU to remove the menus.

1,6

1-5

POWER

2

T-C RESUME FTS SOUND MODE

1 2 3

4 5 6

7 8 9

RETURN		DISPLAY DIM
	0
DISC	É	SYSTEM
MENU		MENU
É	OK É
G	É	H

STOPPLAYPAUSE

ÇÉ Å

SUBTITLE ANGLE ZOOM AUDIO

REPEAT REPEAT SHUFFLE SCAN

A-B

Helpful Hints

•The Player automatically sets the speakers if you set Analog out- put to Dolby Surround. Details are on page 45.

•For the Subwoofer, you cannot adjust the frequency capabilities. Simply choose n (On) or c (Off) to identify whether you connected a subwoofer (n) or not (c).

•Your audio system may refer to the Surround speakers as the

rear speakers.