Philips EXP2460/02 user manual Resume / Hold, ESP, Power Save Mode, Troubleshooting

RESUME / HOLD

RESUME - continuing from where you have stopped

You can store the last position played. When restarting, playback will continue from where you have stopped (RESUME). Use the OFF-RESUME-HOLD slider on the set for this function.

1Switch the slider to RESUME during playback to

activate RESUME.

2 Press 9 whenever you want to stop playback.

3 Press 2; whenever you want to resume playback

➜Playback continues from where you have stopped.

•To deactivate RESUME, switch the slider to OFF.

Helpful Hints:

–For MP3-CD, as it contains large amount of compressed information, resume function will work only before the set is completely shut off.

HOLD- locking all buttons

You can lock the buttons of the set. When a key is pressed, no action will be exe- cuted. With HOLD activated, you can avoid accidental activation of other func- tions.

• Switch the OFF-RESUME-HOLD slider to HOLD to activate HOLD

➜ HOLd is displayed briefly.

➜All buttons are locked and no action will be executed when you press any button on the set.

If the set is switched off, HOLd appears when 2; is pressed.

•To deactivate HOLD, switch the slider to OFF

➜ All the buttons are unlocked.

ESP, POWER SAVE MODE

With a conventional portable CD player, you might have experienced that music stopped (e.g. when you were jogging). The Electronic Skip Protection prevents playback interruption caused by light vibrations and shocks. Continuous playback is ensured. However, ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping!

The power save mode helps to extend battery service life for longer playback.

• Press ESP once or twice during playback.

➜ ESPappears when shock protection is activated

• To deactivate the shock protection and enter the power save mode, press ESP again.

➜ESP disappears.

100 SEC MAGIC ESP!

Average playing times when ESP skip protection activated :

Seconds	track type
100	MP3 (128kbps)
45	Audio CD

Helpful Hints:

– For a MP3 CD, ESP is by default always activated.

TROUBLESHOOTING

WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the warranty. If a fault occurs, first check the points listed before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center.

The CD player has no power, or playback does not start

•Check that your batteries are not empty, that they are inserted correctly, that the contact pins are clean.

•Your adapter connection may be loose. Connect it securely.

The indication nO diSC or nO AF is displayed/CD cannot be read

•Check that the CD is clean and correctly inserted (label-side upward).

•If your lens have steamed up, wait a few minutes until the lens clear up.

•CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.

The indication HOLd is on and/or there is no reaction to controls

•If HOLD is activated, then deactivate it.

•Electrostatic discharge. Disconnect power or remove batteries for a few sec- onds.

Music files do not play

• Check that the file names of MP3 files end with .mp3.

TROUBLESHOOTING

Some directories missing on MP3 CDs

•Check that the total number of files and albums on your MP3 CDs does not exceed 350.

•Only albums with MP3 files are shown.

The CD skips tracks

•The CD is damaged or dirty. Replace or clean the CD.

•Shuffle or program is active. Switch off whichever is on.

Music skips or popping sounds when you play a MP3 track

•Play the music file in your computer. If the problem remains, encode the audio track again and make a new CD.

No sound or bad sound quality

•Playback on pause. Press 2;.

•Loose, wrong or dirty connections. Check and clean connections.

•Volume might not be appropriately adjusted. Adjust the volume.

•Strong magnetic fields. Check the player's position and connections. Also keep away from active mobile phones.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in unsafe oper- ation.