Philips ISP1521 manual

ISP1521

Hi-Speed Universal Serial Bus hub controller

Rev. 03 — 24 November 2004 Product data

1. General description

The ISP1521 is a stand-alone Universal Serial Bus (USB) hub controller IC that

complies with

Universal Serial Bus Speciﬁcation Rev.2.0

. It supports data transfer at

high-speed (480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s).

The upstream facing port can be connected to a Hi-Speed USB host or hub or to an

Original USB host or hub. If the upstream facingpor t is connected to a Hi-Speed USB

host or hub, then the ISP1521 will operate as a Hi-Speed USB hub. That is, it will

support high-speed, full-speed and low-speed devices connected to its downstream

facing ports. If the upstream facing port is connected to an Original USB host or hub,

then the ISP1521 will operate as an Original USB hub. That is, high-speed devices

that are connected to its downstream facing ports will operate in full-speed mode

instead.

The ISP1521 is a full hardware USB hub controller. All Original USB devices

connected to the downstream facing ports are handled using a single Transaction

Translator (TT), when operating in a cross-version environment. This allows the

whole 480 Mbit/s upstream bandwidth to be shared by all the Original USB devices

on its downstream facing ports.

The ISP1521 has seven downstream facing ports. If not used, ports 3 to 7 can be

disabled. The vendor ID,product ID and string descriptors on the hub are supplied by

the internal ROM; they can also be supplied by an external I2C-bus™ EEPROM or a

microcontroller.

The ISP1521 is suitable for self-powered hub designs.

An analog overcurrent detection circuitry is built into the ISP1521, which can also

accept digital overcurrent signals from external circuits; forexample, Micrel MOSFET

switch MIC2026. The circuitry can be conﬁgured to trip on a global or an individual

overcurrent condition.

Each port comes with two status indicator LEDs.

Targetapplications of the ISP1521 are monitor hubs, docking stations for notebooks,

internal USB hub for motherboards, hub for extending Intel® Easy PCs, hub boxes,

and so on.

Contents

Main ISP1521 Hi-Speed Universal Serial Bus hub controller Universal Serial Bus Specication Rev.2.0 Rev. 03 24 November 2004 Product data 1. General description 2. Features Universal Serial Bus Specication Rev.2.0 3. Applications 4. Abbreviations 5. Ordering information Product data Rev. 03 24 November 2004 4 of 53 6. Block diagram Fig 1. Block diagram. ISP1521 Philips Semiconductors ISP1521 Product data Rev. 03 24 November 2004 5 of 53 7. Pinning information Fig 2. Pin conguration. 7.2 Pin description 7.1 Pinning ISP1521BE Page ISP1521 Hub Demo Board Users Guide Page Page 8. Functional description 8.3 Phase-locked loop clock multiplier 8.4 I2C-bus controller 8.5 Overcurrent detection circuit 8.6 GoodLink 8.7 Power-on reset Fig 4. External clock with respect to power-on reset. Fig 3. Power-on reset timing. Stable external clock is to be available at A. 9. Conguration selections 9.1 Conguration through I/O pins Philips Semiconductors ISP1521 pull-up Fig 6. Typical voltage drop components in the self-powered mode using global overcurrent detection. PSWn_N pins have integrated weak pull-up resistors inside the chip. (1) Includes PCB traces, ferrite beads, and so on. Page 9.2 Device descriptors and string descriptors settings using I2C-bus The I C-bus specication Page 9.2.3 ROM or EEPROM map Page Philips Semiconductors ISP1521 Page Page 10. Hub controller description 11. Descriptors Page Page 12. Hub requests Tab le 23 shows the suppor ted standard USB requests. 12.1 Standard USB requests 12.2 Hub class requests Tab le 24 shows the hub class requests. 12.3 Detailed responses to hub requests Page Page 12.4 Various get descriptors bmRequestType 10000000B bmRequest GET_DESCRIPTOR = 6 13. Limiting values 14. Recommended operating conditions In accordance with the Absolute Maximum Rating System (IEC 60134). 15. Static characteristics Page Page 16. Dynamic characteristics C; test circuit Figure 21; unless otherwise specied. Page TPERIOD is the bit duration corresponding with the USB data rate. Fig 11. Source differential data-to-EOP transition skew and EOP width. TPERIOD is the bit duration corresponding with the USB data rate. tJR is the jitter reference point. Fig 13. Receiver SE0 width tolerance. Fig 12. Receiver differential data jitter. Fig 14. Hub differential data delay and SOP distortion. Fig 15. Hub EOP delay and EOP skew. and T within recommended operating range; V =5V; V =V ; V 17. Application information 17.1 Descriptor conguration selection ISP1521 Fig 18. Adjusting analog overcurrent detection limit (optional). . . 17.3 Self-powered hub congurations ISP1521 Fig 19. Self-powered hub; individual port power switching; individual overcurrent detection. Fig 20. Self-powered hub; ganged port power switching; global overcurrent detection. ISP1521 18. Test information DMn D Fig 22. Full-speed test circuit. Fig 21. High-speed transmitter and receiver test circuit. 19. Package outline LQFP80: plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm SOT315-1 Fig 23. LQFP80 package outline. 20. Soldering 20.1 Introduction to soldering surface mount packages Data Handbook IC26; Integrated Circuit Packages 20.2 Reow soldering 20.3 Wave soldering 21. Revision history Philips Semiconductors ISP1521 Contact information 22. Data sheet status 23. Denitions 24. Disclaimers 25. Licenses 26. Trademarks Contents