Philips ISP1521 - page 16

Philips Semiconductors ISP1521

Hi-Speed USB hub controller

Product data Rev. 03 — 24 November 2004 16 of 53

9397 750 13702 © Koninklijke Philips Electronics N.V. 2004. All rights reserved.

Both analog and digital overcurrent modes are supported; see Tab le 7.

For digital overcurrent detection, the normal digital TTL level is accepted on the

overcurrent input pins. For analog overcurrent detection, the threshold is given in the

DC characteristics. In this mode, to ﬁlter out false overcurrent conditions because of

in rush and spikes, a dead time of 15 ms is built into the IC, that is, overcurrent must

persist for 15 ms before it is reported to the host.

9.1.4 Non-removable port

A non-removable port, by deﬁnition, is a port that is embedded inside the hub

application box and is not externally accessible. The LED port indicators

(pins AMBn_N) of such a port are not used. Therefore, the corresponding amber LED

port indicators are disabled to signify that the port is non-removable; see Tab le 8.

More than one non-removable port can be speciﬁed by appropriately connecting the

corresponding amber LED indicators. At least one port should, however, be left as a

removable port.

The detection of any non-removable port sets the hub descriptor into a compound

hub.

9.1.5 Port indicator support

The port indicator support can be disabled by grounding all green port indicators (all

pins GRNn_N); see Tab le 9. This is a global feature. It is not possible to disable port

indicators for only one port.

Table 6: Overcurrent protection mode pin conﬁguration

Power switching mode NOOC PSW1_N PSW2_N PSW3_N PSW4_N PSW5_N PSW6_N PSW7_N

None HIGH ground ground ground ground ground ground ground

Global LOW internal

pull-up ground ground ground ground ground ground

Individual LOW internal

pull-up internal

pull-up internal

pull-up internal

pull-up internal

pull-up internal

pull-up internal

pull-up

Table 7: Overcurrent detection mode selection pin conﬁguration

Pin ADOC Mode selection Description

3.3 Vor 5.0 V analog threshold∆Vtrip

Ground digital normal digital TTL level

Table 8: Non-removable port pin conﬁguration

AMBn_N (n=1to7) Non-removable port

Ground non-removable

Pull-up with amber LED removable

Table 9: Port indicator support: pin conﬁguration

GRN1_N to GRN7_N Port indicator support

Ground not supported

LED pull-up green LED for at least one port supported

Contents

Main ISP1521 Hi-Speed Universal Serial Bus hub controller Universal Serial Bus Specication Rev.2.0 Rev. 03 24 November 2004 Product data 1. General description 2. Features Universal Serial Bus Specication Rev.2.0 3. Applications 4. Abbreviations 5. Ordering information Product data Rev. 03 24 November 2004 4 of 53 6. Block diagram Fig 1. Block diagram. ISP1521 Philips Semiconductors ISP1521 Product data Rev. 03 24 November 2004 5 of 53 7. Pinning information Fig 2. Pin conguration. 7.2 Pin description 7.1 Pinning ISP1521BE Page ISP1521 Hub Demo Board Users Guide Page Page 8. Functional description 8.3 Phase-locked loop clock multiplier 8.4 I2C-bus controller 8.5 Overcurrent detection circuit 8.6 GoodLink 8.7 Power-on reset Fig 4. External clock with respect to power-on reset. Fig 3. Power-on reset timing. Stable external clock is to be available at A. 9. Conguration selections 9.1 Conguration through I/O pins Philips Semiconductors ISP1521 pull-up Fig 6. Typical voltage drop components in the self-powered mode using global overcurrent detection. PSWn_N pins have integrated weak pull-up resistors inside the chip. (1) Includes PCB traces, ferrite beads, and so on. Page 9.2 Device descriptors and string descriptors settings using I2C-bus The I C-bus specication Page 9.2.3 ROM or EEPROM map Page Philips Semiconductors ISP1521 Page Page 10. Hub controller description 11. Descriptors Page Page 12. Hub requests Tab le 23 shows the suppor ted standard USB requests. 12.1 Standard USB requests 12.2 Hub class requests Tab le 24 shows the hub class requests. 12.3 Detailed responses to hub requests Page Page 12.4 Various get descriptors bmRequestType 10000000B bmRequest GET_DESCRIPTOR = 6 13. Limiting values 14. Recommended operating conditions In accordance with the Absolute Maximum Rating System (IEC 60134). 15. Static characteristics Page Page 16. Dynamic characteristics C; test circuit Figure 21; unless otherwise specied. Page TPERIOD is the bit duration corresponding with the USB data rate. Fig 11. Source differential data-to-EOP transition skew and EOP width. TPERIOD is the bit duration corresponding with the USB data rate. tJR is the jitter reference point. Fig 13. Receiver SE0 width tolerance. Fig 12. Receiver differential data jitter. Fig 14. Hub differential data delay and SOP distortion. Fig 15. Hub EOP delay and EOP skew. and T within recommended operating range; V =5V; V =V ; V 17. Application information 17.1 Descriptor conguration selection ISP1521 Fig 18. Adjusting analog overcurrent detection limit (optional). . . 17.3 Self-powered hub congurations ISP1521 Fig 19. Self-powered hub; individual port power switching; individual overcurrent detection. Fig 20. Self-powered hub; ganged port power switching; global overcurrent detection. ISP1521 18. Test information DMn D Fig 22. Full-speed test circuit. Fig 21. High-speed transmitter and receiver test circuit. 19. Package outline LQFP80: plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm SOT315-1 Fig 23. LQFP80 package outline. 20. Soldering 20.1 Introduction to soldering surface mount packages Data Handbook IC26; Integrated Circuit Packages 20.2 Reow soldering 20.3 Wave soldering 21. Revision history Philips Semiconductors ISP1521 Contact information 22. Data sheet status 23. Denitions 24. Disclaimers 25. Licenses 26. Trademarks Contents