DUBBING

Information on DV DubbingGuide to DV and On-Screen Display

This function helps you to easily dub the contents of the DVC (digital video camcorder) to HDD or DVD.

You can control basic operations of the DVC from the remote control of this unit such as playback, fast forward or reverse and stop all operations if the DVC is in video mode. Use the DV cable that has 4-pin input jack and is compliance with the IEEE1394 standards. When you connect to DV-IN jack on the front of this unit, select “L3(DV-IN)” position by using [SOURCE] or [CHANNEL/] on the remote control and press [DISPLAY] to show the DV dubbing information for the operation of your DVC.

Connections Introduction

 

 

 

 

 

 

 

 

When the DVC is

 

 

 

 

 

 

1

 

 

 

in video mode...

 

 

 

 

 

 

 

1/

1

 

1/

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+RW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Control

 

 

DVD

 

 

 

L3 (DV-IN)

 

 

 

 

DV Audio

 

 

Stereo1

 

 

 

AB-1234

 

 

 

 

Start Rec

 

 

 

 

 

 

 

 

0:12:34

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD SP(2Hr)

1h00m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 4

what mode of DVC.

Switch the mode on the DVC to playback mode for the dubbing information.

When the DVC is not

in camera mode...

1/ 1 1/ 1

 

 

 

 

 

+RW

 

 

 

 

 

 

 

 

 

 

L3 (DV-IN)

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AB-1234

 

 

 

 

 

 

 

 

 

0:12:34

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD SP(2Hr)

1h00m

 

 

 

76

Recording Setup Basic

The following instructions are described with the operations using the remote control of this unit.

1. DV icon

2. Indicator of active device

• When “Control” is highlighted,

press [OK] to display the item

selection. Use [K / L] to select the

device you wish to operate, then

press [OK] to activate.

• Select “HDD” / “DVD” to control

this unit.

6.Product name of your DVC

•If the unit cannot recognize the input signal from the DVC or the unknown product, “No Device” or “****” will appear instead.

7.Status of the current operation and the time counter

Each icon means (Available icons may vary depending on the DVC):

Playback

• Select “DV Input” to control your

DVC.

3. Recording audio mode

• With DVC in stop mode while

other sources are available, then

“DV Audio” can be selected. Press

[OK] to display the item selection

and then use [K / L] to select the

audio you wish to output. Press

[OK] again to activate.

• Select “Stereo1” to dub the stereo

sound.

• Select “Stereo2” to dub the sound

with after recording sound.

• Select “Mix” to dub the stereo1

and stereo2.

4. Indicator of dubbing function

• When the unit is ready for

dubbing, “Start Rec” will appear.

• When the unit is dubbing, “Pause

Rec” will appear.

5. Channel position

DVC is in stop mode.

DVC is in playback mode.

DVC is in pause mode.

DVC is fast forwarding. (standard speed)

DVC is fast forwarding. (faster than above) DVC is fast forwarding. (faster than above) DVC is slow forwarding. (standard speed)

DVC is slow forwarding. (faster than above) DVC is slow forwarding. (faster than above)

DVC is fast forwarding. (in stop mode)

DVC is fast reversing. (in stop mode)

DVC is fast reversing. (standard speed) DVC is fast reversing. (faster than above) DVC is fast reversing. (faster than above) DVC is in slow reverse playback.

DVC is recording.

DVC is in recording pause mode.

Others Setup Function Editing

•When you select “L3(DV-IN)” by

using [SOURCE] or

[CHANNEL/], “L3(DV-IN)” will appear.

Español

EN 57