Specifications
Voltage:
Power consumption : 20W
Power consumption (Standby): less than 4W (PWR. in the display switched off)
Rewind time: approx. 100 seconds (cassette E- 180)
Dimensions in cm/ft (WxDxH): 36.0x22.6x9.2 /
1.2x0.3x0.9
Number of video heads : 4
Number of video heads (HIFI): 2
Recording/playback time: 3 hours (SP) (cassette
6 hours (LP) (cassette
Supplied accessories
•Operating instructions
•Remote control and batteries
•Aerial Cable
1. Connecting the video recorder
Important for the United Kingdom
This apparatus is fitted with an approved moulded 10 Amp plug. To change a fuse in this type of plug pro- ceed as follows:
1.Remove fuse cover and fuse.
2.Fix new fuse which should be a BS1362 3A,ASTA or BSI approved type.
3.Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 3A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 3A.
The severed plug must be destroyed to avoid a possi- ble shock hazard should it be inserted into a 13A socket alsewhere.
How to connect a plug:
The wires in the mains lead are coloured in accor- dance with the following code:
BLUE- 'NEUTRAL' ('N')
BROWN- 'LIVE' ('L')
4.The BLUE wire must be connected to the terminal which is marked with the letter 'N' or coloured
BLACK.
5.The BROWN wire must be connected to the termi- nal which is marked with the letter 'L' or coloured RED.
6.Do not connect either wires to the earth terminai in the plug which is marked with the letter 'E' or by the safety earth symbol or coloured green or
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the
Preparing the remote control for operation
The remote control and its
batteries are packed sepa- rately in the original video
recorder packaging. You must install the batteries in the remote control before use.
1.Take the remote control and the enclosed batteries (2 batteries).
2.Open the remote control's battery compartment and place the batteries in it as shown in the picture and close the battery compartment.
The remote control is now ready to use. Its range is approximately 5 metres.
Connecting your video recorder to the TV set
The necessary cable connections
must be made before you can record or playback TV programmes
using your video recorder.
We recommend that you use a scart cable to connect your TV and video recorder.
What is a scart cable?
The scart or Euro AV cable serves as the universal connector for picture, sound and control signals. With this type of connection, there is practically no loss of quality during the picture or sound transfer.
Connecting with a scart cable
Have the following cables ready:
an aerial cable (1, supplied), a scart cable (2, not supplied).
1.Remove the aerial cable plug from | 1 | 2 |
your TV set. Insert it into the |
|
|
AERIAL at the back of the video | AERIAL |
|
recorder. |
|
|
2.Insert one end of the supplied |
|
|
aerial cable into the RF OUT at |
|
|
the back of the video recorder |
|
|
and the other end into the aerial | RF OUT |
|
input socket at the back of the |
|
|
TV set. |
|
|
3.Plug one end of a scart cable |
|
|
into the scart socket AV1(TV) at |
|
|
the back of the video recorder |
|
|
and the other end into the suit- | AV1(TV) |
|
able scart socket on your TV |
|
|
reserved for the video recorder operation (see your TV's operating instructions).
4.Switch on the TV.
5.Insert AC cable into the wall socket.
2 | EN |
|
