BDR-203/BDC-203 Command Reference Manual Version 0.90
4.12.2 Mode Pages
The drive is not supported the Parameters Savable (PS) bit and must be set to zero.
The Page Code field identifies the format and parameters defined for that mode page.
The drive supports following Mode pages.
Table 31 - Mode Page Codes
Page code | Description | Section |
01h | Error Recovery Page | 4.12.2.2 on page 31 |
05h | Write Parameters Page | 4.12.2.5 on page 32 |
08h | Caching Page | 4.12.2.1 on page 31 |
0Eh | CD Audio Control Page | See SFFC |
1Ah | Power Condition Page | 4.12.2.3 on page 31 |
1Dh | 4.12.2.4 on page 31 | |
2Ah | Capabilities & Mechanical Status Page | 4.12.2.6 on page 33 |
3Fh | Return all pages (valid only for the MODE SENSE command) |
|
4.12.2.1 Caching Page
The Caching Page is supported for compatibility of other
Table 32 - Caching Parameter
| Byte | Bit | 7 | 6 | 5 |
|
| 4 | 3 |
| 2 | 1 | 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 |
| PS | Reserved |
|
|
|
| Page Co |
| = 08h |
|
|
|
| 1 |
|
|
|
|
|
| Page Length = 0Ah |
|
|
|
| ||
| 2 |
| IC | ABPF | CAP |
|
| DISC | SIZE |
| WCE | MF | RCD |
|
| 3 |
|
| Demand Read Priority |
|
|
| Write Retention Priority |
|
| ||||
| 4 |
| (MSB) |
|
| Disable |
|
|
|
| ||||
| 5 |
|
|
|
|
|
| (LSB) |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| 6 |
| (MSB) |
|
|
|
| Minimum |
|
|
|
| ||
| 7 |
|
|
|
|
|
|
|
| (LSB) |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| ONFIDENTIAL |
| |||||||
| 8 |
| (MSB) |
| C | Maximum |
|
|
|
| ||||
| 9 |
|
|
|
|
| (LSB) |
| ||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| 10 |
| (MSB) |
|
|
| Maximum |
|
|
|
| |||
| 11 |
|
|
|
|
|
|
| (LSB) |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Default value of the WCE bit is one. D fault value of any other bits and field is zero. |
|
|
|
| |||||||||
4.12.2.2 | Err r Recovery Parameters Page |
|
|
|
|
|
|
|
|
| ||||
| The AWRE a d ARRE bits are not supported and are ignored. |
|
|
|
|
|
| |||||||
| The TB, RC, DTE and DCR bits are ignored. |
|
|
|
|
|
|
|
|
| ||||
| IONEER |
|
|
|
|
|
|
|
|
| ||||
P |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The PER bit and EMCDR field are used to control the defect reporting.
Setting value of the Read Retry Count and the Write Retry Count field are ignored.
4.12.2.3 Power Condition Page
The default value of an Idle bit is one. The default value of the Idle Timer field is 000000c8h (20 second).
The default value of the Standby bit is one. The default value of Standby Timer field is 000012C0h (8 minutes).
4.12.2.4 Time-out & Protect Page
The DISP, SWPP bits are not supported and must be set to 0.
Page 32
