Pioneer DEH-P5100UB installation manual Fastening the front panel, DIN Front/Rear-mount

Installation

English

Installation

English

Connecting the unit English

CD RECEIVER

AUTORADIO CD

RADIO CD

DEH-P5100UB

Note

•Check all connections and systems before final installation.

•Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions.

•Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle.

•Do not install this unit where:

—it may interfere with operation of the vehicle.

—it may cause injury to a passenger as a result of a sudden stop.

•The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet.

•Optimum performance is obtained when the unit is installed at an angle of less than 60°.

2.Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.

Dashboard	Mounting sleeve
182
53

3.Install the unit.

•Use commercially available parts when installing.

Nut

2.Insert the supplied extraction keys into both sides of the unit until they click into place.

3. Tighten two screws on each side.

• Use either truss screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket.

Screw

Dashboard or Console

Factory radio mounting bracket

Note

•When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result.

		CC
	F	A	O				F	O
			N					N
O	F					O	F
					S					S
					T					T
				R	A				R	A
			T					T
ACC position						No ACC position

•	Control signal is output through blue/white cable
	when this unit is powered on. Connect it to an
	external power amp’s system remote control or
	the vehicle’s auto-antenna relay control terminal
	(max. 300 mA, 12 V DC). If the vehicle is equipped
	with a glass antenna, connect it to the antenna
	booster power supply terminal.
•	Never connect blue/white cable to external
	power amp’s power terminal. Also, never connect
	it to the power terminal of the auto antenna.
	Otherwise, battery drain or malfunction may
	result.
•	IP-BUS connectors are color-coded. Be sure to
	connect connectors of the same color.
•	Black cable is ground. This cable and other
	product’s ground cable (especially, high-current
	products such as power amp) must be wired
	separately. Otherwise, fire or malfunction may
	result if they are accidentally detached.

60°

Screw

Firewall or metal support

Metal strap

3. Pull the unit out of the dashboard.

DIN Rear-mount

1. Extend top and bottom of the trim

ring outwards to remove the trim

Fastening the front panel

If you do not plan to detach the front panel, the front panel can be fastened with supplied screw.

•	Use this unit in other than the following
	conditions could result in fire or malfunction.
	— Vehicles with a 12-volt battery and negative
	grounding.
	— Speakers with 50 W (output value) and 4 ohm
	to 8 ohm (impedance value).
•	To prevent short-circuit, overheating or

Installation Manual

Manuel d’installation

Manual de instalación

Printed in Thailand
Imprimé en Thaïlande
<QRD3031-A/N> UC	<KOKNX> <08K00000>

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods.

DIN Front-mount

Installation with metal strap and screws

1.Insert the mounting sleeve into the dashboard.

•When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behind the unit, use factory supplied mounting sleeve.

Screw (M4 8)

•Make sure that the unit is installed securely in place. Unstable installation may cause this unit to malfunction, such as sound skip.

Removing the Unit

1.Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.)

•It becomes easy to remove the trim ring if the front panel is released.

Trim ring

ring. When reattaching the trim ring,

push the trim ring onto the unit until

it clicks. (If the trim ring is attached

upside down, the trim ring will not

fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

Trim ring

2.Determine the appropriate position where the holes on the bracket and the side of the unit match.

Screw

malfunction, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s

negative cables.