Pioneer EFX-1000 manual Other Specifications

OTHER (SPECIFICATIONS)

Symptom		Probably cause		Remedy
When a foot switch is connected,	÷	Foot switch’s logic is reversed (the effector	÷	Use a foot switch with logic matching that
effects are applied even without		applies effects when the foot switch is		of the effector.
pressing the foot switch.		depressed for LOW level).
Effect sounds are distorted.	÷	Input level is too high.	÷	Rotate INPUT LEVEL dial toward left ([MIN]
				direction).
			÷	Try setting IN&OUT LEVEL switch to the
				opposite position.
	÷	Effect output level is too high.	÷	Rotate EFFECT OUT LEV. dial toward left
				([MIN] direction).
	÷	Effect settings are too high (When the DEPTH	÷	Rotate DEPTH dial toward left ([MIN]
		dial is set near its [MAX] position, it may have		direction).
		the effect of raising the volume level.)
Can’t use EFX LINK function	÷	The digital link cable is not connected.	÷	Connect the digital link cable to a DJ mixer
	÷ The connected component is not supported.			(with digital link support)
	÷	The DJ mixer’s settings are incorrect	÷	Set the DJ mixer for EFX LINK.
Can’t use the BPM sync function.	÷	DJ mixer is not connected for EFX LINK.	÷	Connect the DJ CD player and DJ mixer via
	÷ A DJ CD player with digital link support is not			digital link.
		connected to the DJ mixer.
	÷	The BPM measurement mode is not set to	÷	Set the DJ effector’s BPM mode to [AUTO].
		[AUTO].
Echo sounds are output	÷	During echo effect, if DEPTH dial is set to	÷	Rotate DEPTH dial toward the left ([MIN]
continuously		[MAX] and BEAT EFFECTS lever switch is		direction).
		moved from [ON] to [OFF], the feedback
		sound dies not attenuate, producing a hold
		delay effect.
BPM doesn’t count tempo in	÷	Input level is too high, or too low.	÷	Rotate INPUT LEVEL dial so that the input
AUTO mode.				level meter shows around 0 dB.
BPM count is strange.	÷	Some tracks have tempos that prevent them	÷	Set to manual mode and input (TAP) the
		from being measured automatically. (Automatic		tempo manually (P.18)
		measurement range is 70-180 BPM).
MIDI sequencer isn’t	÷	The MIDI sequencer’s sync mode is not set to	÷	Set MIDI sequencer’s sync mode to
synchronized.		“slave”.		“slave.”
	÷	The connected MIDI sequencer is not	÷	A MIDI sequencer without MIDI timing
		supported.		clock cannot be synchronized.

÷This component may fail to operate properly due effects from static electricity or other causes. In this event, try disconnecting the power cord and reconnecting it. If this doesn’t solve the problem, consult your dealer or nearest Pioneer Service Station.

SPECIFICATIONS

1. General

Power supply	AC 110 V - 240 V, 50/60 Hz
Power consumption	16 W
Operating temperature	+5°C to +35°C
Relative humidity	5% to 85% (without condensation)
Weight	2.4 kg
Maximum external dimensions
..........................................................	320 (W) x 234 (D) x 101 (H) mm

2. Audio Unit

Sampling rate	96 kHz
A/D, D/A Resolution	24 bits
Frequency characteristics	20 Hz to 22 kHz
S/N ratio	83 dB
Distortion	0.02 %
Headroom	19 dB
Input level	–10 dBV / +4 dBu (22 kΩ)
Output level	–10 dBV / +4 dBu
	(RCA pin jacks: 1 kΩ, Phone jacks: 1 kΩ)
	*–10 dBV / +4 dBu is switchable.

3. Input/Output terminals
Audio line input terminal
RCA pin jacks	2
Phone jacks (1/4-inch/6.3 mm in diameter)	2
Audio line output terminal
RCA pin jacks	2
Phone jacks (1/4-inch/6.3 mm in diameter)	2
Digital input terminal
RCA pin jack	1
Digital output terminal
RCA pin jack	1
EFX LINK connector (mini-DIN)	1
MIDI input terminal (5-pin DIN)	1
MIDI output terminal (5-pin DIN)	1
4. Accessories
Operating instructions	1
Digital link cable	1
Power cord	1

NOTE:

Specifications and design are subject to possible modification without notice.

26

<DRB1369>