Pioneer PD-F1039 Cautions Regarding Handling, Precautions regarding installation, Storing discs

CAUTIONS REGARDING HANDLING

Precautions regarding installation

•Placing and using the compact disc player for long periods on heat-generating sources such as amplifiers will affect perfor- mance. Avoid placing the player on heat-generating sources.

•Install this compact disc player as far as possible from tuners and TV sets. A compact disc player installed in close proximity to such equipment may cause noise or degrada-

tion of the picture.

•Such noise may be particularly noticeable when

an indoor antenna is used. In such cases, make use of an outdoor antenna, or turn off power to the compact disc player.

•Please place this unit on a level surface.

Cleaning the player

To clean the PLAYER, wipe with a soft, dry cloth. For stubborn dirt, wet a soft cloth with a mild detergent solution made by diluting one part detergent to 5 or 6 parts water, wring well, then wipe off the dirt. Also use a dry cloth to wipe the surface dry. Do not use volatile liquids such as benzene and thinner which are harmful to the unit.

Storing discs

•Discs are made of the same kinds of plastic used for conven- tional analog audio records. Be careful not to allow discs to warp; always store discs in their cases vertically, avoiding locations with high heat or humidity, or extremely low tempera- tures. Avoid leaving discs in cars, since the seat of a car in direct sunlight can become unbelievably hot.

•Always read and abide by the precautionary notes listed on disc labels.

CD lens cleaner

The player's pickup lens should not become dirty in normal use, but if for some reason it should malfunction due to soiling, consult your nearest PIONEER authorized service center. Lens cleaners for CD players are commercially available, but special care should be exercised in their use since some may cause damage to the lens.

Cleaning and handling compact discs

•The presence of fingerprints or smudges on the surface of the disc will not directly affect the recorded signals, but depending on the degree of contamination, the brightness of the light reflected from the signal surfaces may be reduced, causing degradation of sound quality. Always keep your discs clean by wiping them gently with a soft cloth from the inner edge toward the outer periphery.

•If a disc becomes very dirty, dip a soft cloth in water, and after wringing it out well, wipe the dirt away gently, and then remove any water drops with another soft, dry cloth.

•Do not use record cleaning sprays or anti-static agents on discs. Also, never clean discs with benzene, thinner, or other volatile solvents, since damage to the disc surface may result.

Record cleaning

sprays Thinner Benzene

With this player, use discs which display these marks shown below. (Optical audio digital discs.)

Playing CD-R and CD-RW discs in this CD changer

•This unit can play CD-R and CD-RW discs. However, it may not be possible to play unfinalized discs* which have very little recording time left on them.

* What is finalization?

Finalizing a CD-R or CD-RW disc means making a recorded disc playable on an ordinary CD player. In the case of CD-RWs, the player must be specifically compatible with CD-RW discs for it to play them.

•When holding discs, do not touch their signal surfaces. Hold by the edges, or by one edge and the center hole.

•Do not affix gummed labels or tape to the label surfaces. Also, do not scratch or damage the label.

•Discs rotate at high speed inside the player. Do not use damaged (cracked or warped) discs.

•Do not play a CD with a special shape (having other shape than a circular disc, such as a heart shaped disc). Otherwise malfunction may occur.

•The CD accessories (stabilizer protection sheet, protection ring, etc.) which are marketed for improving the sound quality or protecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction.

Re-transporting

When transporting this unit in the future, remove all discs from the rack. Turn off the STANDBY/ON switch, wait for “OFF” to go out from the display. Then unplug the power cord.

Precautions concerning use of optical fiber cables

•Fully insert the optical fiber cable plugs all the way into the jacks.

•Be careful not to fold or crimp the cable. When coiling an optical fiber cable for storage, make sure the diameter of the coil is 15 cm (5-15/16 in.) or larger.

•Use an optical fiber cable with a length of 3 m (10 ft.) or less.

•Protect the optical fiber cable plugs from scratches and dust.

•When the unit is not connected using an optical fiber cable, be sure to keep the protective dust cap plugged into the optical digital output jack at all times.

More than

15 cm

(5-15/16in.)

OPERATING	BEFORE
OPERATIONS	BASIC

OPERATIONS VARIOUS

5