3

 

Basic Setup

5 Select ‘Auto MCACC’ from the Home Menu, then press

ENTER.

Home Menu

 

Home Menu

 

1

. Auto

MCACC

1

. Auto

MCACC

2

. Manual SP Setup

2

. Manual SP Setup

3

. Input

Assign

3

. Input

Assign

4

. Speaker

System

4

. Pre Out

Setting

5

. Video

Parameter

5

. HDMI

Setup

6

. HDMI

Setup

6

. Auto

Power Down

7

. Auto

Power Down

7

. Network

Standby

8

. Network

Standby

8

. FL Demo

Mode

9

. FL Demo

Mode

 

 

 

 

 

VSX-1022

 

VSX-822

•Mic In! blinks when the microphone is not connected to MCACC SETUP MIC jack.

Try to be as quiet as possible after pressing ENTER. The system outputs a series of test tones to establish the ambient noise level.

6 Follow the instructions on-screen.

•Make sure the microphone is connected.

•Make sure the subwoofer is on and the volume is turned up.

•When using surround back or front height speakers, turn on the power to the amplifier to which the surround back or front height speakers are connected, and adjust the sound level to the desired level.

•See below for notes regarding background noise and other possible interference.

7 Wait for the test tones to finish.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

1 . Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Return

•For correct speaker settings, do not adjust the volume during the test tones.

8 Confirm the speaker configuration.

The configuration shown on-screen should reflect the actual speakers you have.

1 . Auto MCACC

Check!

Front

[

YES ]

Center

[

YES ]

Surr

[

YES ]

Surr. Back

[

--- ]

Subwoofer

[

YES ]

10:Next

 

OK

 

Return

•With error messages (such as Too much ambient noise) select RETRY after checking for ambient noise (see Other problems when using the Auto MCACC setup below).

If the speaker configuration displayed isn’t correct, use / to select the speaker and / to change the setting. When you’re finished, go to the next step.

If you see an error message (ERR) in the right side column, there may be a problem with the speaker connection. If selecting RETRY doesn’t fix the problem, turn off the power and check the speaker connections.

9 Make sure ‘OK’ is selected, then press ENTER.

If the screen in step 7 is left untouched for 10 seconds and ENTER is not pressed in step 8, the Auto MCACC setup will start automatically as shown.

1 . Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System

Speaker Distance

Channel Level

Acoustic Cal EQ

Return

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic Calibration EQ.

Again, try to be as quiet as possible while this is happening. It may take 1 to 3 minutes.

24

10The Auto MCACC setup has finished! You return to the

Home Menu.

The settings made in the Auto MCACC setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the Home Menu (starting on page 46).

Note

•Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm

(5 inches) will end up with different size settings. You can correct the setting manually using the Speaker Setting on page 46.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

Other problems when using the Auto MCACC setup

If the room environment is not optimal for the Auto MCACC setup (too much background noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary. If there are any instructions showing in the front panel display, please follow them.

•Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV when doing the Auto MCACC setup.