Pioneer VSX-1022-K, VSX-822-K Note, 100Hz, SMALL, Front, LARGE, SMALL, SMALL, LARGE, X.Over, Height, Home Menu, Subwoofer, Front Height, Pre Out Setting, the PRE OUT L (Single) terminal

	7	Home Menu
	7	Home Menu

1 Select ‘Manual SP Setup’ from the Home Menu.

2 Selectmenu.‘Speaker Setting’ from the Manual SP Setup

- VSX-822 only: You can only adjust the Surr. Back setting

when Pre Out Setting is set to Surr. Back.

- VSX-822 only: If you select one surround back speaker

only, make sure that additional amplifier is hooked up to

the PRE OUT L (Single) terminal.

X.Over

•Default setting: 100Hz

This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer,

2 . Manual SP Setup

a . Speaker Setting

b. X.Over

c. Channel Level

d. Speaker Distance

Return

2a . Speaker	Setting
Front	SMALL
Center	[ SMALL ]
Surr	[ SMALL ]
Surr. Back	[ NO ]
Subwoofer:	YES
	Return

- VSX-1022 only: When using only one surround back

speaker, connect it to the SURROUND BACK L (Single)

terminals.

• Subwoofer – LFE signals and bass frequencies of

channels set to SMALL are output from the subwoofer

when YES is selected (see notes below). Choose the PLUS

setting if you want the subwoofer to output bass sound

and bass sounds playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

•For more on selecting the speaker sizes, see Speaker Setting on page 46.

1 Select ‘Manual SP Setup’ from the Home Menu.

3 Choose the set of speakers that you want to set then select a speaker size.

Use / to select the size (and number) of each of the following speakers:

•Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a subwoofer. Select SMALL to send the bass frequencies to the subwoofer.

•Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO (the center channel is sent to the other speakers).

•Front Height – Select LARGE if your front height speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect front height speakers choose NO.

-You can only adjust the Front Height setting when Pre Out Setting is set to Height.

•Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround speakers choose NO (the sound of the surround channels is sent to the other speakers).

•Surr. Back – Select the number of surround back speakers you have (one, two or none). Select LARGE if your surround back speakers reproduce bass frequencies effectively.

Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.

continuously or you want deeper bass (the bass

frequencies that would normally come out the front and

center speakers are also routed to the subwoofer). If you did

not connect a subwoofer choose NO (the bass frequencies

are output from other speakers).

4 When you’re finished, press RETURN. You return to the Manual SP Setup menu.

Note

•If you select SMALL for the front speakers, the subwoofer will automatically be fixed to YES. Also, the center, surround, surround back and front height speakers can’t be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.

•If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.

•If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due to low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

2 Select ‘X.Over’ from the Manual SP Setup menu.

	2 . Manual SP	Setup	2b . X.Over
	a . Speaker	Setting	Frequency 100Hz
	b . X.Over
	c . Channel	Level
	d . Speaker	Distance
		Return	Return
3
3	Choose the frequency cutoff point.
	Frequencies below the cutoff point will be sent to the

subwoofer (or LARGE speakers).

4 When you’re finished, press RETURN. You return to the Manual SP Setup menu.