08Using other functions
Switching the HDMI output
Set which terminal to use when outputting video and audio signals from the HDMI output terminals.
The HDMI OUT1 terminal is compatible with the Control with HDMI function.
•Press RECEIVER , then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT 1 and HDMI OUT 2 each time the button is pressed.1
Using the Web Control function
The receiver can be operated using a browser from a computer connected on the same LAN as the receiver.
1Turn on the computer and launch the Internet browser.
2In the address bar on the browser, enter the IP address assigned to this receiver.
For example, if the IP address of this receiver is “192.168.0.2”, enter “http://192.168.0.2/”.
When the connection is made with the receiver, a Top Menu will be displayed.
This receiver’s IP address can be found in the ‘IP address, Proxy’ menu (page 85).
3Once the Top Menu is displayed, click the button for the zone you want to operate.
4Operate from the screen for the individual zone.
•Even when the receiver is in the standby mode, it can be turned on using the Web Control function. For details, see Network Standby on page 86.
Top Menu
Web Control |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| Main ZONE |
|
|
| ZONE 2 |
|
|
| ZONE 3 | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| POWER | ON | OFF |
|
| VOLUME |
|
| MUTE |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| INPUT SELECT | DVD |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| LISTENING MODE | STEREO |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
|
| AUTO SURR/ALC/ | HOME |
|
| STANDARD |
| ADVANCED | STEREO |
| |||||
|
| STREAM DIRECT | THX |
|
| SURROUND |
| SURROUND |
| ||||||
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Checking your system settings
Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset.
1Press RECEIVER , then press STATUS to check the system settings.
The front panel display shows each of the following settings for three seconds each: Input function, Sampling Frequency, MCACC preset, ZONE 2 input, ZONE 3 input2 and HDMI OUT.
2When you’re finished, press STATUS again to switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. Set
•Disconnect the iPod and USB memory device from the receiver beforehand.
1Switch the receiver into standby.
2While holding down ENTER on the front panel, press STANDBY/ON.
The display shows RESET NO .
3Select ‘RESET’ using PRESET /, then press
ENTER on the front panel. The display shows RESET? OK.
4Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
•Note that all settings will be saved, even if the receiver is unplugged.
Note
1• The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI OUT 1, then select the synchronized amp mode on the TV using the TV’s remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3, or BD.
2The ZONE 3 input are only displayed for the
64
En