Pioneer VSX-709RDS manual Remote Control VSX-609RDS, Receiver button see, Menu button

Displays & Controls

Remote Control (VSX-609RDS)

ë￿ =

MULTI CONTROL

1DVD/LD TV/SAT VCR/DVR CD

DSP MODE (see pages 39)

Use to put receiver in one of the DSP modes. To use first press the RECEIVER button then operate this button.

MIDNIGHT (see page 41)

Use to put receiver in Midnight mode. To use,

2

CD-R/

RECEIVER TUNER TAPE/MD TVCONT

2DSPMODE MIDNIGHT 5.1CH

1 2 3 4

first press the RECEIVER button, then operate this button.

5.1 CH (see page 40)

	CHANNEL	TEST	ATT		SIGNAL
3	SELECT	TONE			SELECT
	5	6	7		8
	CHANNEL		EFFECT
	LEVEL						~
	9	0	10		DISC
		FUNC	CH
4	VOL	TV CONTROL			VOL
		FQ
	ST		ST				!
5		ENTER			TOP
	MENU
					MENU		@
		FQ
6	SOURCE CLASS		MPX		BAND
		7￿	8￿			3
	D.ACCESS		CHANNEL				#
7			DISPLAY		RF ATT
	1￿	Á￿		4￿		¢￿
8	LOUDNESS FUNCTION		MUTING				$
		FL REMOTE MASTER					%
9
	RECEIVER DIMMER		SETUP	VOLUME

0AUDIO/VIDEOPRE-PROGRAMMED

- REMOTECONTROLUNIT ^

1MULTI CONTROL buttons

Use to put the receiver/remote control in the stated mode.

For other equipment controls, see Controlling the Rest of Your System on pages 52 – 55.

2RECEIVER button (see page 15)

Use this button when setting up the surround sound for the receiver.

3Number/Mode buttons (see pages 22, 43)

Use the number buttons to select the radio frequency in tuner Direct access mode or the tracks in CD, DVD mode etc.

Also, buttons marked with the following names have special functions. If you try to use one of these functions but the display flashes it means that function cannot be used in the current mode (for example DSP modes cannot be used when

5.1CH setting is on).

2(see pages 38, 39)

Use to put receiver in Dolby Digital, Dolby Surround and DTS modes. To use first press the RECEIVER button then operate this button.

When the DVD/LD or DVD 5.1 CH function is selected each press switches the DVD/LD input between DVD/LD and DVD 5.1 CH. To use, first press the RECEIVER button, then operate this button.

CHANNEL SELECT (see page 21)

Use to select a speaker when setting up the surround sound of the receiver. To use, first press the RECEIVER button, then operate this button.

TEST TONE (see page 21)

Use to sound the TEST TONE when setting up the surround sound of the receiver. To use, first press the RECEIVER button, then operate this button.

ATT

Use to attenunate (lower) the level of an analog input signal and prevent distortion (refer to p.34

!, @). To use, first press the RECEIVER button, then operate this button.

CHANNEL LEVEL +/– (see page 21)

Use to set up the levels of the surround sound of the receiver. To use, first press the RECEIVER button, then operate this button.

SIGNAL SELECT (see page 36)

Use to select the proper signal (analog, digital) for the source your are inputting. To use, first press the RECEIVER button, then operate this button.

4TV CONTROL buttons

The following four sets of buttons are dedicated TV controls.

FUNC button

Use to select the TV function.

button

Use to turn on the power of the TV.

CH +/– buttons

Use to change channels on your TV.

VOL +/– buttons

Use to adjust the volume on your TV.

5MENU button

Use to access different menus associated with your DVD player.

32

En