Manuals / Pioneer / Home Audio / Stereo System

Pioneer VSX-D309 manual Connecting Speakers, Connecting Your System, Speaker terminals

Models: VSX-D309

1 48

Download 48 pages 61.82 Kb

Page 12

Connecting Speakers

Connecting Your System

Connecting Speakers

Connect your speakers as shown below. Be sure to connect each speaker to the appropriate speaker terminal, and also to connect the positive and negative terminals correctly (so that the same wire is connected to the positive terminal of the receiver and the positive terminal of the speaker, and likewise with the negative). When connecting equipment, always make sure the power switched off and the power cord is disconnected from the wall outlet.

• Use speakers with a nominal impedance of 8 Ω to 16 Ω.

Front	Powered	Front
(left)	sub-woofer	(right)
		Center

INPUT

R	L
AM LOOP
ANTENNA IN	CD
			CONTROL
O				COAX	OPT
U			OUT	PCM/2/DTS
T				PCM/2/DTS
	VCR/	VIDEO		DIGITAL	IN
	DVR
IN		IN	OUT

		TV/		TO	FRONT	CENTER
	IN	TV/	IN	MONITOR	SPEAKERS	SPEAKER
		SAT		TV
		DVD		SUB	R	L
	IN	DVD	IN	SUB
	IN	/LD	IN	WOOFER
		FRONT		PREOUT
FM				SURROUND
UNBAL	R	OUT		SURROUND
UNBAL	R		R	L
75Ω	E
75Ω	C	CD-R
FM		CD-R
ANTENNA		/TAPE
	P	/MD
	L	IN		CENTER
	A	IN		CENTER
	Y

SURROUND
SPEAKERS		AC OUTLET

R	L

SUB	DVD 5.1 CH
WOOFER	INPUT

Surround (right)

Speaker terminals

Use good quality speaker wire to connect the speakers to the receiver.

1Twist around 1/2 inch of bare wire strands together.

2 Unclip the speaker terminal and insert the wire.

3 Snap shut the speaker terminal to secure.

Surround

(left)

» á

12

Image 12

Pioneer VSX-D309 manual Connecting Speakers, Connecting Your System, Speaker terminals

Contents

VSX-D309 Operating InstructionsAUDIO/VIDEO MULTI-CHANNELRECEIVER IMPORTANT NOTICE For Canadian modelInformation to User For Canadian modelIMPORTANT SAFETY INSTRUCTIONS Features Remote Control of Other ComponentsDTS* Digital Theater Systems decoder equipped Dolby** Digital and Dolby Pro LogicTable of Contents Set up OperationChecking the Supplied Accessories Using this ManualInstalling the Receiver When Making Cable ConnectionsPreparing the Remote Control Set upOperating range of remote control unit Loading the batteriesConnecting Your System Connecting AntennasUsing external antennas FM wire antennaConnecting Audio Components Set upCassette deck placement Connecting Your SystemConnecting DVD 5.1 Channel Components Connecting Video ComponentsConnecting Your System VCR, DVR, etcConnecting Digital Components Set upConnecting Your System 7Digital audio cords/Optical cablesConnecting Speakers Connecting Your SystemSpeaker terminals AC OUTLET SWITCHED 100 W 0.8 A MAX Set upHints on speaker placement Connecting Your SystemSetting Up for Surround Sound Preparations1Press RECEIVER to turn the power on 4Press %or Þto select the setting you want to setSet up SPEAKER Front, Center, Surround setting modePreparations SUB WOOFER ON/PLUS/OFF setting mode Crossover frequency setting modeLFE attenuator setting mode Press % or Þ to select sub woofer ON, PLUS or OFFSet up Low cut filter ON/OFF setting modeFRONT speakers distance setting mode CENTER speaker distance setting modeDynamic range control setting mode Dual mono settingMONO settings Coaxial digital input setting1 2 5 4,6 3Set up Optical digital input settingSetting Up the Remote Control 2 3 2 1,4Recalling preset codes 2Press the MULTI CONTROL button for theSet up be controlled, enter the 3 digit setup code5Press REMOTE SET UP to exit the preset mode 4Point the remote toward the component toClearing the Remote Control Settings Direct FunctionTo turn the DIRECT funtion OFF the default setting is ON, press REMOTE SET UP andDisplays & Controls Front PanelOperation Display 8SIGNAL SELECT indicatorsDisplays & Controls Remote Control OperationDisplays & Controls Displays & Controls FUNC buttonSound Modes Learning about the Sound ModesOperation STANDARD modeSwitching ANALOG/DIGITAL Signal Input Playing a SourceDIGITAL lights when a Dolby Digital signal is input, DTS lights when a DTS signal is inputPlaying Sources with Dolby Digital or DTS Sound procedure. Refer to “Playing a source” on2Press SIGNAL SELECT to select DIGITAL 3Press 2to switch the Dolby/DTS mode onSelecting a Sound Mode DSP mode1Press RECEIVER 2Press DSP MODE to select the sound modeUsing MIDNIGHT Listening Mode ADVANCED THEATER mode Dolby Digital/DTS mode1Press RECEIVER DTS on the front panelUsing the Tuner Finding a Station1Press the TUNER button on the remote control 2Use the BAND button to change the bandTuning Directly to a Station Memorizing Stations1Press the TUNER button on the remote control 3Press D. ACCESS DIRECT ACCESSRecalling Memorized Stations 1Press the TUNER button on the remote controlUsing the Tuner 3Press CLASS to select one of the three classesMaking a Recording Making an Audio or a Video Recordingremote control of the source component OperationControlling the Rest of Your System CD/MD/CD-R/VCR/LDPlayer ControlsSOURCE 9MENUCassette Deck Controls OperationControlling the Rest of Your System 1 SOURCEDVD/DVR Player Controls Controlling the Rest of Your System1 SOURCE 53 ¢DTV Controls @STANDBY/ON powerOperation Controlling the Rest of Your SystemCable TV/Satellite TV/TV Controls STANDBY/ON powerControlling the Rest of Your System modeTroubleshooting Additional InformationSymptom CauseSymptom Additional InformationCause RemedyPreset Code List Additional InformationSpecifications Additional InformationAmplifier Section • EIA To establish a safe levelDecibel Level Example Page Page 8 0 0 – 4 2 1 – 1 4 0