MOUNTING THE ATH1 TRANSPORT
1.DO NOT CONNECT POWER TO THE TRANSPORT AT THIS TIME.
2. | Position the flat side of the | ATH1/M380 Attachment Bag Contents |
|
|
|
|
|
|
|
|
|
| ||||||||
motorized transport against the bottom |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Pivot screw as |
|
| ||||
|
|
|
|
|
|
| ||||||||||||||
side of the Attachment Plate so that the |
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
| assembled |
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
transport logo is toward the screen and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
the center “M” hole in the Attachment |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Attachment |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| ||||||||||||||
Plate is aligned with the front recessed |
|
|
|
|
|
|
|
|
| Plate |
| |||||||||
transport hole. Insert the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
screw up through the transport and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Attachment Plate and loosely complete |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
the assembly with the corresponding |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
washer, lock washer and nut. Now |
|
|
| ATH1 mount |
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
loosely insert the four small 3/8” screws |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
through the four remaining “M” slots through the top of the Attachment Plate and down into the transport.
M hole
M slots
3.Refer to the ATH1 user manual (included with ATH1) for additional instructions to install the lens at this time, but do not forget to complete the “Final Adjustments” step below.
ATTACHING THE PROJECTOR TO THE CEILING MOUNT
Insure that the RPA mount head is secure (see instructions included with the RPA mount) and oriented properly relative to the 7/8” socket head screw heads so that the mounted projector will face the screen. Use two people to lift and position the projection assembly so that the heads of each of the 7/8” socket head screws rest within the matching final location of the RPA mount head. At this point the silver 3/8” spacers should be between the Attachment Plate and the RPA mount head. The projection assembly may be lowered to allow the 7/8” screw heads to rest on the RPA mount. However, a first person should continue to guide the projection assembly while and a second person uses the gold assembly wrench to tighten the 7/8” screws. When tightening these screws, do so in a pattern of incrementally driving each screw a little more into the attachment plate so that at any time the projection assembly is resting on as many screw heads as possible until all are tightened.
Planar
Page 8
