Manuals / Brands / Computer Equipment / Network Router / Planet Technology / Computer Equipment / Network Router

Planet Technology ADE-4120 3.4Factory Default Settings, 4.DHCP server, 1.Web Configurator, ISP setting in WAN side, 3.4.1Username and Password, 3.4.2 LAN and WAN Port Addresses

1 47

Download 47 pages, 4.37 Mb

PLANET ADE-4120 ADSL Firewall Router

6.Click OK to finish the configuration.

3.4Factory Default Settings

Before configurating this ADE-4120, you need to know the following default settings.

1.Web Configurator

Does not require user name and password

2.Device IP Network settings in LAN site IP Address : 192.168.1.254

Subnet Mask : 255.255.255.0

3.ISP setting in WAN side Bridge (RFC1483 bridge)

4.DHCP server

DHCP server is enabled. Start IP Address : 192.168.1.1 End IP Address : 192.168.1.100

3.4.1Username and Password

The web interface does not require username and password by default. You can select “Basic” -> “User Profile” to enable the administrator authentication.

If you ever forget the password to log in, you may press the RESET button for more than 5 seconds to restore the factory default settings..

3.4.2 LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values

Contents

Page Copyright Disclaimer FCC Compliance Statement CE mark Warning Trademarks Table of Contents Page Chapter 1. Introduction 1.1 An Overview of the ADE-4120 1.2Package Contents 1.3ADE-4120Features PLANET ADE-4120ADSL Firewall Router Multi-Protocol to Establish A Connection: Network Address Translation (NAT): Firewall: 1.4 ADE-4120Application Chapter 2. Using the Router 2.1 Cautions for using the ADE-4120 2.2 The Front Panel LEDs 2.3 The Rear Ports 2.4 Cabling Chapter 3. Configuration 3.1 Before Configuration 3.2Connecting the ADE-4120 3.3Configuring PC in Windows Start / Settings / Control Panel Network Configuration TCP / IP NE2000 Compatible DNS Configuration Disable DNS “OK” 3.3.2For Windows NT4.0 Protocols 2.Select TCP/IP Protocol and click Properties 3.3.3For Windows Network and Dial-up Connections 2.Double-click LAN Area Connection 4. Select Internet Protocol (TCP/IP) and click Properties 3.3.4For Windows XP Page 3.4Factory Default Settings 3.5 Information from the ISP 3.6 Configuring with the Web Browser 3.6.2.1 Setup 1 System parameters 3.6.2.2 Setup 2 LAN parameters 3.6.2.3 Setup 3 WAN parameters 3.6.2.4 Setup 4 VC parameters 3.6.2.5 Setup 5 Dial parameters 3.6.2.6 Step 6 Confirm parameters 3.6.3 Basic 3.6.3.1 User profile 3.6.3.2 Log table display setting 3.6.3.3 Packet filter 3.6.3.4 User access control 3.6.3.5 DHCP 3.6.3.6 Forward 3.6.3.7 Multiple NAT and Multiple DMZ 3.6.3.8 DMZ 3.6.3.9 DDNS 3.6.3.10 Save & Restart 3.6.4 Advance 3.6.4.1 Static route 3.6.4.2 RIP 3.6.4.3 Save & Restart 3.6.5 Utility 3.6.5.1 System 3.6.5.2 Firmware upgrade 3.6.5.3 Load default settings 3.6.5.4 Save & Restart 3.6.6 Monitor Chapter 4. Troubleshooting Appendix A. Specification Appendix B. FAQ and Product Support How do I get Napster to work with the Router How can I not receive corrupted FTP downloads Does the ADSL Router support IPsec Will the Router function in a Macintosh environment With which type of firewall is the ADSL router equipped Why can't I connect to the Web Configurator Why is that i can ping to outside hosts, but not access Internet websites Appendix C Glossary DMT Downstream rate DSLAM Dynamic IP Addresses Encapsulation Internet address Internet Protocol (IP) IP address ISP MAC Remote server RFC Route Router routing table Subnet TCP TFTP Telnet Transparent bridging