Typical Installation, continued
For the ground connection, also use the largest gauge cable available. Connect to the terminal marked GND and then connect this cable directly to your car’s chassis. Keep the length of the GND connection as short as possible, ideally under 6", to avoid ground loops and engine noise hum prob- lems. Make certain that the ground point is directly connect- ed to the car’s metal chassis, with no dirt or paint getting in the way of a clean
7.SECURELY install the amplifier in your chosen location. Take the time to secure the amplifier solidly so that it does not come loose in the event of a collision or sud- den jolt to the vehicle. Warning: Low Flying Amp!
8.CONNECT the positive and negative power wires to the amplifier. A fuse near the amplifier is not necessary.
9.CONNECT the remote
10.CONNECT the RCA signal input cables to the amplifier.
11.CONNECT the speaker wires to the amplifier.
Make sure to use speaker wire of at least 16 gauge or thicker. Be certain to maintain correct polarity. One of the terminals on the rear of your speaker is positive (+) and the other is negative
Make certain that no bare wire ends touch each other. Such contact could result in an electrical short and cause your head unit or amplifier to turn off
or malfunction.
12.Carefully review the amplifier’s control settings to make sure that they are set according to the needs of your system.
13.Now install the power wire fuse and reconnect the negative battery post terminal. (See your authorized Polk AutoSound Dealer for professional advice on fuses and circuit breakers.)
14.Turn on the head unit at low level to check that the amplifier is configured correctly. Resist the tempta-
15.Make the necessary adjustments to the input sensitivi- ty to obtain the right overall output and the desired bal- ance between the two pairs of channels and other amps in your system.
ADDITIONAL STEPS AND DIFFERENT PROCEDURES MAY BE REQUIRED IN SOME APPLICATIONS. IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT YOUR AUTHORIZED POLK AUDIO AUTOSOUND DEALER OR POLK AUDIO CUSTOMER SERVICE.
Installation typique, suite
6.Trouvez un point de contact métallique solide où faire le raccord de mise à la masse et
Pour le raccord à la masse, utilisez toujours le plus gros calibre de câble possible. Connectez le câble à la borne identifiée GND (masse) puis raccordez ce câble directement au châssis du véhicule. Le câble de masse doit être aussi court que possible – idéalement moins de 15 cm (6 po) - pour éviter les bruits causé par l’induction du système électrique du moteur et par les boucles de masse.
7.Installez l’amplificateur à l’endroit déterminé.
8.Connectez les câbles positifs et négatifs à l’amplificateur.
Il n’est pas nécessaire d’installer un fusible près de l’amplificateur.
9.Connectez le fil de « l’interrupteur à distance » à l’amplificateur. 10.Connectez les câbles RCA de signal d’entrée à l’amplificateur.
11.Connectez les fils des
12.Vérifiez attentivement le réglage des contrôles de l’amplifica- teur pour vous assurer qu’ils sont conformes aux caractéris- tiques de votre chaîne.
13.Installez maintenant le fusible du câble d’alimentation positif et reconnectez le câble négatif à la borne négative de la bat- terie. (Consultez votre revendeur agréé Polk AutoSound pour des conseils professionnels sur les fusibles et les disjonc- teurs.)
14.Allumez l’unité de source à bas volume pour vérifier sa con- formité à l’amplificateur. RÉSISTEZ à la tentation de monter le volume avant d’avoir vérifié le réglage de tous des contrôles.
15.Faites les ajustements nécessaires à la sensibilité du gain d’entrée pour obtenir la sortie globale appropriée et l’équilibre désiré entre les deux paires de canaux et les autres amplifica- teurs de votre chaîne.
DES ÉTAPES ET DES PROCÉDURES ADDITIONNELLES POUR- RAIENT ÊTRE REQUISES POUR CERTAINES APPLICATIONS. SI VOUS AVEZ DES QUESTIONS, COMMUNIQUEZ AVEC VOTRE REVENDEUR AGRÉÉ POLK AUDIO AUTOSOUND OU CON- TACTEZ LE SERVICE À LA CLIENTÈLE DE POLK AUDIO.
9