TO START THE ENGINE

Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains car- bon monoxide, an odorless and deadly gas.

1. Open the fuel shut-off valve.

2.Move the choke control located on the engine to the “Choke” position.

NOTE: No choke is required on warm engines. make sure choke is in the “RUN” position on warm engine starts.

3. On the engine there is a ON/OFF switch located on the front panel of the engine. Place this switch to the "ON" position.

4.Grasp handle on rope starter and pull slowly until resistance is felt. Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary.

5.When engine starts, gradually move the choke to the “RUN” position

IMPORTANT: Allow generator to run at no load for 5 minutes upon each initial start-up to allow engine and generator to stabilize.

STOPPING ENGINE

1.Disconnect all electrical loads.

2.Turn ON/OFF switch to "OFF" position.

3. Close fuel shut-off valve.

CONNECTING ELECTRICAL LOADS

1.Let engine run and warm up for five minutes after starting with no electrical load.

Connect loads in the following manner to prevent dam- age to equipment:

2.Connect inductive load equipment first, inductive loads consist of refrigerators, freezers, water pumps, air conditioners, or small hand tools. Connect the items that require the most wattage first. See Wattage Calculation Section in this manual.

3.Connect the lights next.

4.Voltage sensitive equipment should be the last equipment connected to the generator. Plug volt- age sensitive appliances such at TV's, VCR's, mi- crowaves, ovens, computers, and cordless tele- phones into a UL listed voltage surge protector, then connect the UL listed voltage surge protector to the generator.

Failure to connect and operate equipment in this sequence can cause damage to equipment and will void the warranty on your generator.

Follow the wattage calculation table in the Wattage Calculation section of this manual. Overloading the generator will cause power fluctu- ations and can damage equipment and appli- ances.

Porter-Cable Corporation will only be responsible for damage to customer's equipment when the generator is determined to be defective. This determination will only be made by an authorized representative of Porter-Cable Corporation and this decision will be final. Porter-Cable Corporation reserves the right to inspect the elec- trical connections at the customer's site of opera- tion and test the generator for proper operation before any determination of liability is made. Failure to maintain the equipment or wiring for inspection will void any claim for damages by the customer. Porter-Cable Corporation will not be responsible for equipment damaged as a result of voltage surges, improper operation or improper installation of the generator.

12 — ENG

Page 11 Page 13
Page 12
Image 12
Porter-Cable BSI550 instruction manual To Start the Engine, Stopping Engine, Connecting Electrical Loads
Page 11 Page 13

BSI550 specifications

The Porter-Cable BSI550 is a versatile and powerful tool designed for both professionals and DIY enthusiasts who need a robust solution for their fastening and drilling tasks. With its innovative features and reliable performance, the BSI550 stands out in the crowded market of power tools.

One of the main highlights of the BSI550 is its powerful motor. This tool is engineered to deliver a robust output, providing ample torque for a wide range of applications, from driving screws into hard materials to drilling through tough surfaces. With variable speed settings, users can easily adjust the speed according to the task at hand, allowing for greater precision and control.

Another impressive feature of the Porter-Cable BSI550 is its integrated clutch system. This technology helps to prevent over-tightening and stripping of screws, ensuring that each fastener is driven to the correct depth without damaging the material. This is especially beneficial for those working with delicate surfaces or smaller fasteners where precision is crucial.

The BSI550 is also designed for user comfort and convenience. Its ergonomic handle is crafted to reduce fatigue during extended use, allowing users to work for longer periods without discomfort. The lightweight design enhances maneuverability, making it easier to use in tight spaces or overhead applications.

Additionally, the tool features an LED work light that illuminates the work area, providing better visibility in low-light conditions. This feature is particularly advantageous for professionals working in dimly lit environments or for DIYers tackling projects at home in the evening.

For those who value versatility, the Porter-Cable BSI550 is compatible with a variety of bits and attachments. This adaptability makes it suitable for various tasks beyond basic drilling and fastening, expanding its functionality for diverse projects.

In summary, the Porter-Cable BSI550 is a powerful, reliable, and user-friendly tool that excels in providing both performance and comfort. Its advanced features, including a powerful motor, integrated clutch system, ergonomic design, and LED work light, make it a top choice for anyone looking to enhance their toolkit with a dependable fastening solution. Whether you are a seasoned professional or a DIY enthusiast, the BSI550 delivers impressive results and enhances productivity on the job.
Top Page Image Contents