Tractor

CUSTOMER RESPONSIBILITIES

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

	TRAILING	MANDREL
	TRAILING	ASSEMBLY
	EDGE UP	ASSEMBLY
	EDGE UP
	BLADE
		CENTER
		HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT	BLADE
OR PIN

FIG. 13

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

183041 specifications

The Poulan 183041 is an essential tool for homeowners and landscaping professionals alike, designed to make yard work more efficient and manageable. Known for its reliability and ease of use, the Poulan 183041 is a high-quality gas-powered string trimmer that stands out in the realm of outdoor power equipment.

One of the main features of the Poulan 183041 is its robust 25cc two-cycle engine. This powerful engine delivers ample power for trimming grass, weeds, and tough brush, making it suitable for a variety of landscaping tasks. The lightweight design, weighing approximately 10 pounds, ensures that users can maneuver the trimmer easily, reducing fatigue during extended use.

The trimmer is equipped with an easy-start system, which allows users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms. Furthermore, the Poulan 183041 has a straight shaft design, providing extended reach for trimming in hard-to-reach areas like under bushes and fences.

The dual-line cutting system is another significant characteristic of this model. It utilizes a 0.080-inch line, which offers a practical balance between durability and cutting ability. The bump feed mechanism allows for quick and efficient line advancement, ensuring that users can maintain trimming without interruptions.

The Poulan 183041 also features an adjustable handle, which provides users the flexibility to customize their grip for optimal comfort and control. Combined with anti-vibration technology, it significantly reduces hand fatigue and enhances the overall user experience.

Moreover, the trimmer’s design includes a protective debris guard, which minimizes the risk of projectiles while trimming, promoting safety during operation.

In addition to these features, Poulan emphasizes ease of maintenance with the 183041 model. Regular upkeep is straightforward, reducing downtime and prolonging the equipment's lifespan. This trimmer is engineered for convenience, allowing users to focus on their lawn care tasks efficiently.

Overall, the Poulan 183041 is a dependable and versatile string trimmer that delivers power and comfort, making it an excellent choice for anyone looking to maintain their yard with ease. Whether tackling tough weeds or giving the edges a clean finish, this model proves to be an indispensable asset for landscaping efforts.

Poulan 183041 owner manual Tractor

Models: 183041