SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 23)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

Depress clutch/brake pedal and engage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

 

NUT

 

1-9/16"

“A”

JAM NUT

 

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 23

TO REPLACE MOTION DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 25)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

21

Page 21
Image 21
Poulan 183041 owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig, Transmission REMOVAL/REPLACEMENT

183041 specifications

The Poulan 183041 is an essential tool for homeowners and landscaping professionals alike, designed to make yard work more efficient and manageable. Known for its reliability and ease of use, the Poulan 183041 is a high-quality gas-powered string trimmer that stands out in the realm of outdoor power equipment.

One of the main features of the Poulan 183041 is its robust 25cc two-cycle engine. This powerful engine delivers ample power for trimming grass, weeds, and tough brush, making it suitable for a variety of landscaping tasks. The lightweight design, weighing approximately 10 pounds, ensures that users can maneuver the trimmer easily, reducing fatigue during extended use.

The trimmer is equipped with an easy-start system, which allows users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms. Furthermore, the Poulan 183041 has a straight shaft design, providing extended reach for trimming in hard-to-reach areas like under bushes and fences.

The dual-line cutting system is another significant characteristic of this model. It utilizes a 0.080-inch line, which offers a practical balance between durability and cutting ability. The bump feed mechanism allows for quick and efficient line advancement, ensuring that users can maintain trimming without interruptions.

The Poulan 183041 also features an adjustable handle, which provides users the flexibility to customize their grip for optimal comfort and control. Combined with anti-vibration technology, it significantly reduces hand fatigue and enhances the overall user experience.

Moreover, the trimmer’s design includes a protective debris guard, which minimizes the risk of projectiles while trimming, promoting safety during operation.

In addition to these features, Poulan emphasizes ease of maintenance with the 183041 model. Regular upkeep is straightforward, reducing downtime and prolonging the equipment's lifespan. This trimmer is engineered for convenience, allowing users to focus on their lawn care tasks efficiently.

Overall, the Poulan 183041 is a dependable and versatile string trimmer that delivers power and comfort, making it an excellent choice for anyone looking to maintain their yard with ease. Whether tackling tough weeds or giving the edges a clean finish, this model proves to be an indispensable asset for landscaping efforts.