TO REMOVE WHEELS (See Fig. 21)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualifi ed service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

 

IMPORTANT: It is important to prevent gum deposits from

 

forming in essential fuel system parts such as carburetor,

 

fuel hose, or tank during storage.Also, alcohol blended fuels

 

(called gasohol or using ethanol or methanol) can attract

 

moisture which leads to separation and formation of acids

 

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

 

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective cover that does not retain moisture.Do not use plastic.Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

Page 18
Image 18
Poulan 187877 owner manual Storage, Other

187877 specifications

The Poulan 187877 is a robust and versatile tool that is designed to meet the needs of both amateur gardeners and professional landscapers. This equipment is particularly recognized for its powerful performance and user-friendly features, making it an excellent choice for a variety of outdoor tasks.

One of the main features of the Poulan 187877 is its potent engine. Equipped with a high-performance two-stroke engine, this model delivers impressive horsepower, ensuring that it can tackle demanding tasks with ease. This engine design not only provides powerful cutting capabilities but also minimizes emissions, adhering to environmental regulations.

Another significant characteristic of the Poulan 187877 is its lightweight construction. Weighing in at just the right amount, this tool allows for extended use without causing fatigue to the operator. Its ergonomic handle design offers a comfortable grip, promoting efficient operation during extended periods of use, whether you're trimming hedges, cutting fallen branches, or undertaking other landscaping activities.

The Poulan 187877 also features an advanced starting system, incorporating a reliable recoil starter that reduces the effort required to start the engine. This feature is particularly advantageous for users who often experience difficult starts in colder weather or are looking for a hassle-free starting experience.

In terms of technology, the Poulan 187877 incorporates an easy-to-access air filter system that simplifies maintenance. This design allows users to clean or replace the filter quickly, ensuring that the tool maintains optimal performance over time. Additionally, the model’s adjustable choke helps adapt to varying conditions, making it versatile in different environments.

The cutting mechanism of the Poulan 187877 is another standout feature. With its sharp, durable blades, the tool provides clean cuts that promote healthy plant growth. The cutting width is sufficient for most tasks, enabling efficient yard maintenance without requiring multiple passes.

Safety is a priority with the Poulan 187877, which includes essential features such as a chain brake and a protective guard that prevent accidental injuries during operation. These safety mechanisms inspire confidence in users, allowing them to focus on their tasks.

In summary, the Poulan 187877 is an impressive piece of equipment that combines power, safety, and user-friendly features. Its robust engine, lightweight design, efficient starting system, and easy maintenance make it a great addition to any gardener's toolkit.