Before Starting the Engine, ADD Gasoline See Fig

OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already ﬁ lled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil ﬁ ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overﬁ ll.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

•Fill fuel tank to bottom of tank ﬁ ller neck. Do not over- ﬁ ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open ﬂame.

CAUTION: Alcohol blended fuels (called gas- ohol or using ethanol or methanol) can attract moisture which leads to separation and for- mation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next sea- son. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

187877 specifications

The Poulan 187877 is a robust and versatile tool that is designed to meet the needs of both amateur gardeners and professional landscapers. This equipment is particularly recognized for its powerful performance and user-friendly features, making it an excellent choice for a variety of outdoor tasks.

One of the main features of the Poulan 187877 is its potent engine. Equipped with a high-performance two-stroke engine, this model delivers impressive horsepower, ensuring that it can tackle demanding tasks with ease. This engine design not only provides powerful cutting capabilities but also minimizes emissions, adhering to environmental regulations.

Another significant characteristic of the Poulan 187877 is its lightweight construction. Weighing in at just the right amount, this tool allows for extended use without causing fatigue to the operator. Its ergonomic handle design offers a comfortable grip, promoting efficient operation during extended periods of use, whether you're trimming hedges, cutting fallen branches, or undertaking other landscaping activities.

The Poulan 187877 also features an advanced starting system, incorporating a reliable recoil starter that reduces the effort required to start the engine. This feature is particularly advantageous for users who often experience difficult starts in colder weather or are looking for a hassle-free starting experience.

In terms of technology, the Poulan 187877 incorporates an easy-to-access air filter system that simplifies maintenance. This design allows users to clean or replace the filter quickly, ensuring that the tool maintains optimal performance over time. Additionally, the model’s adjustable choke helps adapt to varying conditions, making it versatile in different environments.

The cutting mechanism of the Poulan 187877 is another standout feature. With its sharp, durable blades, the tool provides clean cuts that promote healthy plant growth. The cutting width is sufficient for most tasks, enabling efficient yard maintenance without requiring multiple passes.

Safety is a priority with the Poulan 187877, which includes essential features such as a chain brake and a protective guard that prevent accidental injuries during operation. These safety mechanisms inspire confidence in users, allowing them to focus on their tasks.

In summary, the Poulan 187877 is an impressive piece of equipment that combines power, safety, and user-friendly features. Its robust engine, lightweight design, efficient starting system, and easy maintenance make it a great addition to any gardener's toolkit.

Poulan 187877 Before Starting the Engine, To Adjust Skid Plates See Fig, ADD Gasoline See Fig

Models: 187877