Chute Weldment, Deflector Weldment, Deflector Seal

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600)

CONTROL PANEL / CHUTE

		2
		11
		10
		5
		8
	3	6
		6
		9
		11
	6	4
	6	11
		11

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	404770X428	CHUTE WELDMENT
2	178633X428	DEFLECTOR WELDMENT
3	420325	DEFLECTOR SEAL
4	179096X479	STRAP
5	189713X428	KNOB BLACK
6	128415	POP RIVET
7	185600	SHOULDER BOLT 1/4−20 X .704
01.09.001-A 8	72270505	CARRIAGE BOLT 5/16−18 X .625
9	191730	NUT 1/4−20
10	155415	WASHER
11	179246	PLASTIC WASHER

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 24

Page 24

Image 24

Poulan 428496 owner manual Chute Weldment, Deflector Weldment, Deflector Seal, Strap, Knob Black, POP Rivet, Plastic Washer

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Electric start button used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting 01.07.004-C KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BAR Auger Bearing Bearing Plug Chute Weldment Deflector WeldmentDeflector Seal Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Panel Bracket LH Panel Bracket RH Handle GripLower Tube Pivot Support Spacer RetainerKnob RED Handle Knob Impeller ROD Traction RODShifter ROD TOP Shifter ROD Bottom Console Panel Interlock SpringInterlock CAM Torsion Spring Repair Parts Snow Thrower - Model Number PP208E24 Drive Speed Selector Assembly Drive Plate AssemblyWheelhub END Plate Axle Shaft Roll PIN 3/16Sprocket Clik PIN Cover Assembly Complete LCT EngineFrame 423184X428 Impeller Belt Traction BeltIdler ARM Idler Bushing Wheel Assembly LH 187831X421187866X421 Safety Ignition KEY 422663 DECAL, Danger DECAL, DANGER, DeflectorDECAL, Instruction DECAL, Auger Lever RT Service Notes Service Notes Limited Warranty

Poulan 428496 Chute Weldment, Deflector Weldment, Deflector Seal, Strap, Knob Black, POP Rivet

Models: 428496 96198002600

KEY

CHUTE WELDMENT

DEFLECTOR WELDMENT

DEFLECTOR SEAL

STRAP

KNOB BLACK

POP RIVET

PLASTIC WASHER