Axle Shaft, Roll PIN 3/16, Sprocket, Clik PIN

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600)

DRIVE

	6
1b	4
7	3
	3
1b
6	1a

			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
		2	1	188226	(assy of 1a,1b) AXLE ASSEMBLY
		3	1a	179352	AXLE SHAFT
		3	1b	9465M	ROLL PIN 3/16
5	4		1b	9465M	ROLL PIN 3/16
5	4	01.03.005-B	2	402691	SPROCKET
		01.03.005-B	2	402691	SPROCKET
			3	174697	THRUST WASHER
			4	179830	BEARING
			5	17490508	BOLT 5/16−18 X .500
			6	155443	CLIK PIN
			7	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 32

Image 32

Poulan 428496, 96198002600 owner manual Axle Shaft, Roll PIN 3/16, Sprocket, Clik PIN

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Electric start button used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting 01.07.004-C KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BAR Auger Bearing Bearing Plug Chute Weldment Deflector WeldmentDeflector Seal Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Panel Bracket LH Panel Bracket RH Handle GripLower Tube Pivot Support Spacer RetainerKnob RED Handle Knob Impeller ROD Traction RODShifter ROD TOP Shifter ROD Bottom Console Panel Interlock SpringInterlock CAM Torsion Spring Repair Parts Snow Thrower - Model Number PP208E24 Drive Speed Selector Assembly Drive Plate AssemblyWheelhub END Plate Axle Shaft Roll PIN 3/16Sprocket Clik PIN Cover Assembly Complete LCT EngineFrame 423184X428 Impeller Belt Traction BeltIdler ARM Idler Bushing 187866X421 Wheel Assembly LH187831X421 Safety Ignition KEY 422663 DECAL, Danger DECAL, DANGER, DeflectorDECAL, Instruction DECAL, Auger Lever RT Service Notes Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600)

KEY

AXLE SHAFT

ROLL PIN 3/16

SPROCKET

CLIK PIN