Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 96198002600, 428496 owner manual Unfold Upper Handle, Install Speed Control ROD See Figs

Models: 428496 96198002600

1 40

Download 40 pages 28.93 Kb

Page 5

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Poulan 96198002600 Unfold Upper Handle, Install Speed Control ROD See Figs, Install Traction Drive Control ROD See Figs

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEY Electric start button used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting 01.07.004-C KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BAR Bearing Plug Auger Bearing Deflector Weldment Chute WeldmentDeflector Seal Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Handle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot Support Retainer SpacerKnob RED Handle Knob Traction ROD Impeller RODShifter ROD TOP Shifter ROD Bottom Interlock Spring Console PanelInterlock CAM Torsion Spring Repair Parts Snow Thrower - Model Number PP208E24 Drive Drive Plate Assembly Speed Selector AssemblyWheelhub END Plate Roll PIN 3/16 Axle ShaftSprocket Clik PIN Complete LCT Engine Cover AssemblyFrame 423184X428 Traction Belt Impeller BeltIdler ARM Idler Bushing 187866X421 Wheel Assembly LH187831X421 422663 Safety Ignition KEY DECAL, DANGER, Deflector DECAL, DangerDECAL, Instruction DECAL, Auger Lever RT Service Notes Service Notes Limited Warranty