KEY Part NO. NO. Description | Poulan 96198002801, 430429 specs

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY PART

NO. NO. DESCRIPTION

1175321X479 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18

12163183 SCREW 5/16-18 X .625

13427145 IMPELLER HUB

14427154 IMPELLER SLEEVE

15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING

35407767 SCREW 5/16-18 X .750

36427317 GEARBOX COVER LH

37

192090

SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Image 23

Poulan 96198002801, 430429 owner manual KEY Part NO. NO. Description

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR 23 22 KEY Part NO. NO. Description Bearing Plug Auger Bearing Deflector Weldment Deflector Control AssemblyDeflector Spring 15 420679 Service Part Deflector Control Chute Weldment Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Pivot Support Loop Handle LHLoop Handle RH Lower Tube Handle Knob SpacerRetainer Knob RED Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOP Interlock Stop Interlock SpringInterlock CAM Torsion Spring Clik PIN Axle ShaftRoll PIN 3/16 Sprocket Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector 428685 Frame427928X428 Engine Mounting Plate Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket 187865X421 Wheel Assembly LH187833X421 KEY Part NO. no Safety Ignition KEY428498 DECAL, DANGER, Deflector 181037DECAL, Danger KEY Part Description QTY MANUFACTURER’S Warranty Coverage Warranty II. Emission Control System Warranty Warranty Limited Warranty