Chute Weldment, Deflector Weldment, Knob Black | Poulan 96198002801

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CONTROL PANEL / CHUTE

5

7

15

3

16

				*14		*11
						*11
				2		10
					6	10
				4	6
				4
				6		*13
						*13
KEY	PART	DESCRIPTION		1		*12
NO.	NO.	DESCRIPTION		1		*12
1	420315X428	CHUTE WELDMENT
2	178633X428	DEFLECTOR WELDMENT
3	420673	DEFLECTOR CONTROL ASSEMBLY
4	420325	DEFLECTOR SEAL
5	414280	KNOB BLACK	6
6	128415	POP RIVET	6
6	128415	POP RIVET			9
7	17501010	SCREW 10-24 X .625		8	9	01.09.015-A
8	430324	CHUTE SNOW SHIELD		8		01.09.015-A
8	430324	CHUTE SNOW SHIELD
9	419822X004	SHIELD RETAINER STRAP
*10	179829	SHOULDER BOLT 1/4-20 X .375
*11	191730	NUT 1/4-20
*12	72250505	CARRIAGE BOLT 3/8-16 X .625
*13	751153	NUT 5/16-18
*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16420672 (SERVICE PART) DEFLECTOR CABLE Black

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECES- SARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

25

Image 25

Poulan 96198002801 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal, Knob Black, POP Rivet

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting KEY Part Description Auger HousingScraper BAR Auger 27 LH 23 22 KEY Part NO. NO. Description Bearing Plug Auger Bearing Deflector Spring 15 420679 Service Part Deflector Control Deflector Control AssemblyChute Weldment Deflector Weldment Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Loop Handle RH Loop Handle LHLower Tube Pivot Support Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Interlock CAM Interlock SpringTorsion Spring Interlock Stop Roll PIN 3/16 Axle ShaftSprocket Clik PIN Exploded Drive Plate Assembly AssemblySpeed Selector Rubber Ring 427928X428 FrameEngine Mounting Plate 428685 Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley 187833X421 Wheel Assembly LH187865X421 428498 Safety Ignition KEYKEY Part NO. no DECAL, Danger 181037DECAL, DANGER, Deflector KEY Part Description QTY MANUFACTURER’S Warranty Coverage Warranty II. Emission Control System Warranty Warranty Limited Warranty