Auger Housing, Scraper BAR, Auger Bearing

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303)

AUGER HOUSING / IMPELLER ASSEMBLY

		KEY	PART	DESCRIPTION
	3 (5x)	NO.	NO.	DESCRIPTION
	3 (5x)	1	404929X428	AUGER HOUSING 27
	4 (5x)	1	404929X428	AUGER HOUSING 27
	4 (5x)	2	404932X431	SCRAPER BAR
2		2	404932X431	SCRAPER BAR
2		3	72270505	CARRIAGE BOLT 5/16−18 X .625
		4	155377	NUT 5/16−18
	01.07.002-A

2	3

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	420478	AUGER BEARING
3		2	411939	BEARING PLUG
	01.07.024-B	3	179582	SCREW 5/16−18 X 1.00
	01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 24

Image 24

Poulan 437126, 96198003303 owner manual Auger Housing, Scraper BAR, Auger Bearing, Bearing Plug

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See Fig Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing Plug Auger 27 LH Auger 27 RHSkid Plate LH Skid Plate RH Deflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Loop Handle LH Loop Handle RHLower Handle Pivot Support Weldment Spacer RetainerKnob RED Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PP1150E27 Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate Axle Shaft Sprocket ENGINE, B&S Frame436146X428 Engine Mount Plate Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley 428684 Wheel Assembly LH Cable Bracket LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch Slide Safety Ignition KEY 193071 01.14.012-A Shifter ROD TOP Shifter ROD Bottom 181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, Instruction Service Notes Limited Warranty

KEY

AUGER HOUSING 27

SCRAPER BAR

KEY

AUGER BEARING

BEARING PLUG