LEVER/CABLE Rotator Assembly, Rotator Head | Poulan 96198003303

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303)

CONTROL PANEL / CHUTE

2

2

*3

1

*7

*6

*4	01.09.010-B	*5

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1428272 LEVER/CABLE ROTATOR ASSEMBLY

217501010 SCREW 10-24 X .625

*3	420678	ROTATOR HEAD
*4	405932	ROTATOR PIVOT BRACKET
*5	420675	PULLEY PIVOT
*6	428273	CABLE ASSEMBLY ADJUSTABLE
*7	428310	CABLE ASSEMBLY HEAT SHIELD

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

2

		1	01.15.009-A
KEY	PART	1
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	421249	STEER CABLE
2	74041024	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27

Image 27

Poulan 96198003303, 437126 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot, Steer Cable

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger Bearing Skid Plate RH Auger 27 LHAuger 27 RH Skid Plate LH Chute Snow Shield 419822X431 Shield Retainer Strap Deflector SealKnob Black POP Rivet Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Pivot Support Weldment Loop Handle LHLoop Handle RH Lower Handle Handle Knob SpacerRetainer Knob RED Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Flood Headlight Wire HarnessConsole Panel Headlight Bezel Repair Parts Snow Thrower - Model Number PP1150E27 Drive END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Sprocket Axle Shaft Engine Mount Plate ENGINE, B&SFrame 436146X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket 428684 Wheel Assembly LH Cable Bracket LHCable Bracket RH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe 193071 Safety Ignition KEY Shifter ROD TOP Shifter ROD Bottom 01.14.012-A DECAL, Instruction 181037DECAL, Danger DECAL, DANGER, Deflector Service Notes Limited Warranty