Deflector Seal, Knob Black, POP Rivet | Poulan 437126, 96198003303

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303)

CONTROL PANEL / CHUTE

5

7

15

3

16

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1435023X428 CHUTE WELDMENT

2178633X428 DEFLECTOR WELDMENT

3420673 DEFLECTOR CONTROL ASSEMBLY

	4	420325	DEFLECTOR SEAL	6
	5	414280	KNOB BLACK	6
	5	414280	KNOB BLACK
	6	128415	POP RIVET

717501010 SCREW 10-24 X .625

8430324 CHUTE SNOW SHIELD

9419822X431 SHIELD RETAINER STRAP

*10	179829	SHOULDER BOLT 1/4-20 X .375
*11	191730	NUT 1/4-20
*12	72250505	CARRIAGE BOLT 3/8-16 X .625
*13	751153	NUT 5/16-18
*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16420672 (SERVICE PART) DEFLECTOR CABLE BLACK

*14		*11
		*11
2		*10
	6	*10
4	6
4

6	*13

1

*12

9

8 01.09.015-B

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Image 26

Poulan 437126 Deflector Seal, Knob Black, POP Rivet, Chute Snow Shield 419822X431 Shield Retainer Strap, Deflector Spring

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing Plug Skid Plate LH Auger 27 LHAuger 27 RH Skid Plate RH POP Rivet Deflector SealKnob Black Chute Snow Shield 419822X431 Shield Retainer Strap Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Handle Loop Handle LHLoop Handle RH Pivot Support Weldment Knob RED SpacerRetainer Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Headlight Bezel Wire HarnessConsole Panel Flood Headlight Repair Parts Snow Thrower - Model Number PP1150E27 Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate Axle Shaft Sprocket 436146X428 ENGINE, B&SFrame Engine Mount Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley 428684 Cable Bracket RH Wheel Assembly LHCable Bracket LH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 193071 01.14.012-A Shifter ROD TOP Shifter ROD Bottom DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Instruction Service Notes Limited Warranty