To Remove Wheels See Fig, Carburetor, Engine Speed | Poulan 437390

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

Fig. 22

ENGINE

SEE ENGINE MANUAL.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a Sears service center/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a Sears service center/ department, which has the proper equipment and experi- ence to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

Fig. 23

18

Image 18

Poulan 437390, 96198003601 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Scraper BAR Auger HousingKEY Part Description Auger 27 LH Exploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Skid Plate LH Auger BearingBearing Plug Skid Plate RH Chute Snow Shield Knob BlackPOP Rivet Shield Retainer Strap Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Tube Loop Handle LHLoop Handle RH Pivot Support Knob RED SpacerRetainer Handle Knob Impeller ROD Traction ROD Headlight Bezel Wire HarnessConsole Panel Flood Headlight 01.03.005-B Exploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate 427963X428 Complete LCT EngineFrame Engine Mounting Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Wheel Assembly LH 432335X421432336X421 Safety Ignition KEY 422663 181037 DECAL, Danger Service Notes Limited Warranty